ST STM32G473 User Manual

General-purpose timers (TIM15/TIM16/TIM17) RM0440
1400/2126 RM0440 Rev 4
Bits 9:8 CC2S[1:0]: Capture/Compare 2 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC2 channel is configured as output
01: CC2 channel is configured as input, tim_ic2 is mapped on tim_ti2
10: CC2 channel is configured as input, tim_ic2 is mapped on tim_ti1
11: CC2 channel is configured as input, tim_ic2 is mapped on tim_trc. This mode is working only if an
internal trigger input is selected through TS bit (TIM15_SMCR register)
Note: CC2S bits are writable only when the channel is OFF (CC2E = ‘0’ in TIM15_CCER).
Bits 7:4 IC1F[3:0]: Input capture 1 filter
This bit-field defines the frequency used to sample tim_ti1 input and the length of the digital filter
applied to tim_ti1. The digital filter is made of an event counter in which N consecutive events are
needed to validate a transition on the output:
0000: No filter, sampling is done at f
DTS
0001: f
SAMPLING
=f
tim_ker_ck
, N=2
0010: f
SAMPLING
=f
tim_ker_ck
, N=4
0011: f
SAMPLING
=f
tim_ker_ck
, N=8
0100: f
SAMPLING
=f
DTS
/2, N=6
0101: f
SAMPLING
=f
DTS
/2, N=8
0110: f
SAMPLING
=f
DTS
/4, N=6
0111: f
SAMPLING
=f
DTS
/4, N=8
1000: f
SAMPLING
=f
DTS
/8, N=6
1001: f
SAMPLING
=f
DTS
/8, N=8
1010: f
SAMPLING
=f
DTS
/16, N=5
1011: f
SAMPLING
=f
DTS
/16, N=6
1100: f
SAMPLING
=f
DTS
/16, N=8
1101: f
SAMPLING
=f
DTS
/32, N=5
1110: f
SAMPLING
=f
DTS
/32, N=6
1111: f
SAMPLING
=f
DTS
/32, N=8
Bits 3:2 IC1PSC[1:0]: Input capture 1 prescaler
This bit-field defines the ratio of the prescaler acting on CC1 input (tim_ic1). The prescaler is reset as
soon as CC1E=’0’ (TIM15_CCER register).
00: no prescaler, capture is done each time an edge is detected on the capture input
01: capture is done once every 2 events
10: capture is done once every 4 events
11: capture is done once every 8 events
Bits 1:0 CC1S[1:0]: Capture/Compare 1 selection
This bit-field defines the direction of the channel (input/output) as well as the used input.
00: CC1 channel is configured as output
01: CC1 channel is configured as input, tim_ic1 is mapped on tim_ti1
10: CC1 channel is configured as input, tim_ic1 is mapped on tim_ti2
11: CC1 channel is configured as input, tim_ic1 is mapped on tim_trc. This mode is working only if an
internal trigger input is selected through TS bit (TIM15_SMCR register)
Note: CC1S bits are writable only when the channel is OFF (CC1E = ‘0’ in TIM15_CCER).

ST STM32G473 Specifications

General

Brand	ST
Model	STM32G473
Category	Microcontrollers
Language	English