Symmetricom TimeProvider 2700 User Manual

098-00564-000 Revision A3 – July, 2013 TimeProvider 2300/2700 User’s Guide 67
Chapter 3
TimeProvider 2300/2700 CLI Command Set
|....|........|.......|.......|................................................|
|32 |event |enable |0 |"SYNCE/T1E1 input SSM changed" |
|....|........|.......|.......|................................................|
|51 |minor |enable |0 |"Incompatible transport type" |
|....|........|.......|.......|................................................|
|52 |minor |enable |0 |"PTP input lost" |
|....|........|.......|.......|................................................|
|53 |event |enable |0 |"PTP master switched" |
|....|........|.......|.......|................................................|
|54 |event |enable |0 |"PTP time/frequency input not traceable" |
|....|........|.......|.......|................................................|
|71 |minor |enable |0 |"PTP server near client limit on ETH2" |
|....|........|.......|.......|................................................|
|72 |event |enable |0 |"PTP client dropped from ETH2 client list" |
|....|........|.......|.......|................................................|
|73 |event |enable |0 |"PTP client added to ETH2 client list" |
|....|........|.......|.......|................................................|
|74 |event |enable |0 |"PTP client list on ETH2 refreshed" |
|....|........|.......|.......|................................................|
|75 |event |enable |0 |"PTP state changed to disabled on ETH2" |
|....|........|.......|.......|................................................|
|76 |event |enable |0 |"PTP state changed to listening on ETH2" |
|....|........|.......|.......|................................................|
|77 |event |enable |0 |"PTP state changed to master on ETH2" |
|....|........|.......|.......|................................................|
|78 |event |enable |0 |"PTP state changed to passive on ETH2" |
|....|........|.......|.......|................................................|
|91 |minor |enable |0 |"GNSS receiver communications failed" |
|....|........|.......|.......|................................................|
|92 |minor |enable |0 |"GNSS receiver not tracking satellite" |
|....|........|.......|.......|................................................|
|93 |minor |enable |0 |"GNSS signal low" |
|....|........|.......|.......|................................................|
|94 |major |enable |0 |"GNSS antenna voltage out of range" |
|....|........|.......|.......|................................................|
|95 |major |enable |0 |"GNSS antenna current out of range" |
|....|........|.......|.......|................................................|
|96 |minor |enable |0 |"GNSS antenna short-circuit" |
|....|........|.......|.......|................................................|
|97 |minor |enable |0 |"GNSS antenna open-circuit" |
|....|........|.......|.......|................................................|
|111 |minor |enable |0 |"Ethernet port link down" |
|....|........|.......|.......|................................................|
|112 |minor |enable |0 |"Excessive traffic on port ETH{1|2}" |
|....|........|.......|.......|................................................|
|113 |minor |enable |0 |"Unsupported SFP on ETH{1|2}" |
|....|........|.......|.......|................................................|
|131 |critical|enable |0 |"Power out of range" |
|....|........|.......|.......|................................................|
|132 |critical|enable |0 |"Operational failure" |
|....|........|.......|.......|................................................|
|133 |major |enable |0 |"Battery(-48V)-A failure" |
|....|........|.......|.......|................................................|
|134 |major |enable |0 |"Battery(-48V)-B failure" |
|....|........|.......|.......|................................................|
|135 |critical|enable |0 |"FPGA failure" |
|....|........|.......|.......|................................................|
|136 |critical|enable |0 |"Flash partition failure" |
|....|........|.......|.......|................................................|

Symmetricom TimeProvider 2700 Specifications

General

Brand	Symmetricom
Model	TimeProvider 2700
Category	Network Hardware
Language	English