EasyManuals Logo

Symmetricom TimeProvider 2700 User Manual

Symmetricom TimeProvider 2700
338 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #66 background imageLoading...
Page #66 background image
66 TimeProvider 2300/2700 User’s Guide 098-00564-000 Revision A3 – July, 2013
Chapter 3
TimeProvider 2300/2700 CLI Command Set
show alarm-config
Displays the alarm configuration including alarm ID, severity, state, reporting delay
and description for the TP 2300/2700 alarms. This also displays if the alarm is
transitory.
Command Syntax:
show alarm-config
Example:
TP2700> show alarm-config
Response :
--------------------------------------------------------------------------------
|ID |Severity|State |Delay |Event/Alarm Descriptions |
|----|--------|-------|-------|------------------------------------------------|
|1 |minor |enable |0 |"Entered time/frequency warm-up state" |
|....|........|.......|.......|................................................|
|2 |minor |enable |0 |"Entered time/frequency free-run state" |
|....|........|.......|.......|................................................|
|3 |event |enable |0 |"Entered time/frequency fast-track state" |
|....|........|.......|.......|................................................|
|4 |event |enable |0 |"Entered time/frequency normal-track state" |
|....|........|.......|.......|................................................|
|5 |event |enable |0 |"Entered time/frequency bridging state" |
|....|........|.......|.......|................................................|
|6 |minor |enable |0 |"Entered time/frequency holdover state" |
|....|........|.......|.......|................................................|
|7 |major |enable |0 |"Entered time/frequency ext holdover state" |
|....|........|.......|.......|................................................|
|8 |minor |enable |0 |"Entered time/frequency holdover rec state" |
|....|........|.......|.......|................................................|
|21 |minor |enable |0 |"GNSS/SYNCE/PTP/T1E1 input poor quality" |
|....|........|.......|.......|................................................|
|22 |event |enable |0 |"GNSS/PTP input time qualified" |
|....|........|.......|.......|................................................|
|23 |event |enable |0 |"GNSS/SYNCE/PTP/T1E1 input freq qualified" |
|....|........|.......|.......|................................................|
|24 |event |enable |0 |"GNSS/PTP input selected as time reference" |
|....|........|.......|.......|................................................|
|25 |event |enable |0 |"GNSS/SYNCE/PTP/T1E1 input sel as freq ref" |
|....|........|.......|.......|................................................|
|26 |minor |enable |0 |"T1E1 input Loss Of Signal (LOS)" |
|....|........|.......|.......|................................................|
|27 |minor |enable |0 |"T1E1 input Alarm Indication Signal (AIS)" |
|....|........|.......|.......|................................................|
|28 |minor |enable |0 |"T1E1 input Out Of Frame (OOF)" |
|....|........|.......|.......|................................................|
|29 |minor |enable |0 |"T1E1 input CRC error (CRC)" |
|....|........|.......|.......|................................................|
|30 |minor |enable |0 |"T1E1 input Bipolar Violation (BPV)" |
|....|........|.......|.......|................................................|
|31 |minor |enable |0 |"T1E1 input frequency error" |

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Symmetricom TimeProvider 2700 and is the answer not in the manual?

Symmetricom TimeProvider 2700 Specifications

General IconGeneral
BrandSymmetricom
ModelTimeProvider 2700
CategoryNetwork Hardware
LanguageEnglish