YASKAWA GA700 - Page 650

10.22 Parameters Changed by PM Motor Code Selection
650 YASKAWA ELECTRIC SIEP C710617 05F YASKAWA AC Drive GA700 Technical Manual
No. Name Unit Motor Code (setting value of E5-01)
E1-09
Minimum Output
Frequency
Hz 4.4 4.4 4.4 4.4 4.4 4.4 4.4 4.4
C5-17 Motor Inertia kgm
2
0.046 0.055 0.064 0.116 0.140 0.259 0.31 0.42
L3-24
*1
Motor Accel Time
for Inertia Cal
s 0.102 0.101 0.098 0.130 0.127 0.193 0.191 0.187
n5-02
Motor
Acceleration Time
s 0.102 0.101 0.098 0.130 0.127 0.193 0.191 0.187
n8-49
d-Axis Cur
forHighEfficiency
Cont
% -16.5 -11.3 -12.8 -16.8 -15.6 -10.7 -9.6 -13.3
*1 Default settings vary depending on the setting of o2-04 (Drive Model Selection).
Table 10.8 SSR1 Series Motor Code Setting for Specification of 400 V at 1750 min
-1
(r/min)
No. Name Unit Motor Code (setting value of E5-01)
E5-01
PM Motor Code
Selection
- 1232 1233 1235 1236 1238 123A 123B 123D
Voltage Class V 400 400 400 400 400 400 400 400
Capacity kW 0.4 0.75 1.5 2.2 3.7 5.5 7.5 11
Motor Rotation
Speed
min
-1
1750 1750 1750 1750 1750 1750 1750 1750
E5-02
PM Motor Rated
Power (kW)
kW 0.4 0.75 1.5 2.2 3.7 5.5 7.5 11.0
E5-03
PM Motor Rated
Current (FLA)
A 0.89 1.56 2.81 4.27 7.08 10.31 13.65 20.7
E5-04
PM Motor Pole
Count
- 6 6 6 6 6 6 6 6
E5-05
PM Motor
Resistance (ohms/
phase)
Ω 25.370 9.136 6.010 3.297 1.798 0.982 0.786 0.349
E5-06
PM d-axis
Inductance (mH/
phase)
mH 169.00 92.08 67.71 34.40 32.93 22.7 16.49 13.17
E5-07
PM q-axis
Inductance (mH/
phase)
mH 197.50 119.56 81.71 54.00 37.70 26.80 23.46 15.60
E5-09
PM Back-EMF
Vpeak (mV/(rad/
s))
mVs/rad 392.6 440.6 478.3 466.3 478.8 478.1 520.0 481.5
E5-24
PM Motor
Induced Voltage
Constant 2 (Ke)
mV/(r/
min)
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
E1-04
Maximum Output
Frequency
Hz 87.5 87.5 87.5 87.5 87.5 87.5 87.5 87.5
E1-05
Maximum Output
Voltage
V 380.0 380.0 380.0 380.0 380.0 380.0 380.0 380.0
E1-06 Base Frequency Hz 87.5 87.5 87.5 87.5 87.5 87.5 87.5 87.5
E1-09
Minimum Output
Frequency
Hz 4.4 4.4 4.4 4.4 4.4 4.4 4.4 4.4
C5-17 Motor Inertia kgm
2
0.0011 0.0017 0.0023 0.0043 0.0083 0.014 0.017 0.027
L3-24
*1
Motor Accel Time
for Inertia Cal
s 0.092 0.076 0.051 0.066 0.075 0.083 0.077 0.084
n5-02
Motor
Acceleration Time
s 0.092 0.076 0.051 0.066 0.075 0.083 0.077 0.084
n8-49
d-Axis Cur
forHighEfficiency
Cont
% -8.6 -11.5 -10.3 -19.8 -8.5 -11.0 -18.6 -12.5