EasyManuals Logo

Yealink T40G Administrator's Guide

Yealink T40G
622 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #29 background imageLoading...
Page #29 background image
Phone Network
9
T42G/T42S/T41P/T41S/T40P/T40G/T27P/T27G/T23P/T23G/T21(P) E2/T19(P) E2:
Menu->Settings->Advanced Settings (default password: admin)->Network->WAN
Port->IPv4->Static IPv4 Client->Default Gateway
Parameter
static.network.static_dns_enable
[1]
<y0000000000xx>.cfg
Description
It triggers the static DNS feature to on or off.
Note: It works only if “static.network.internet_port.type” is set to 0 (DHCP).
Permitted
Values
0-Off, the IP phone will use the IPv4 DNS obtained from DHCP.
1-On, the IP phone will use manually configured static IPv4 DNS.
Default
0
Web UI
Network->Basic->IPv4 Config->Static DNS
Phone UI
T54S/T52S/T48S/T48G/T46S/T46G/T29G:
Menu->Advanced (default password: admin) ->Network->WAN
Port->IPv4->Type(DHCP)->Static DNS
T42G/T42S/T41P/T41S/T40P/T40G/T27P/T27G/T23P/T23G/T21(P) E2/T19(P) E2:
Menu->Settings->Advanced Settings (default password: admin) ->Network->WAN
Port->IPv4->DHCP IPv4 Client->Static DNS
Parameter
static.network.primary_dns
[1]
<y0000000000xx>.cfg
Description
It configures the primary IPv4 DNS server.
Example:
static.network.primary_dns = 202.101.103.55
Note: It works only if “static.network.ip_address_mode” is set to 0 (IPv4) or 2 (IPv4 &
IPv6). In DHCP environment, you also need to make sure
static.network.static_dns_enable" is set to 1 (On).
Permitted
Values
IPv4 Address
Default
Blank
Web UI
Network->Basic->IPv4 Config->Static IP Address->Primary DNS
Phone UI
T54S/T52S/T48S/T48G/T46S/T46G/T29G:
Menu->Advanced (default password: admin)->Network->WAN Port->IPv4->Static
IP->Primary DNS
Or Menu->Settings->Advanced (default password: admin)->Network->WAN
Port->IPv4->DHCP->Static DNS (Enabled) ->Primary DNS
T42G/T42S/T41P/T41S/T40P/T40G/T27P/T27G/T23P/T23G/T21(P) E2/T19(P) E2:
Menu->Settings->Advanced Settings (default password: admin)->Network->WAN
Port->IPv4->Static IPv4 Client->Pri.DNS
Or Menu->Settings->Advanced Settings (default password: admin)->Network->WAN

Table of Contents

Other manuals for Yealink T40G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yealink T40G and is the answer not in the manual?

Yealink T40G Specifications

General IconGeneral
SIP Accounts3
Wall MountableYes
Opus CodecNo
Display2.3 inch 132x64-pixel graphical LCD
NetworkDual-port Gigabit Ethernet
PoEYes
Headset SupportYes, RJ9 port
Power AdapterOptional
Voice CodecsG.722, G.711(A/μ), G.729AB, G.726
Local Phonebook1000 entries

Related product manuals