EasyManuals Logo

Cisco 10000 Series User Manual

Cisco 10000 Series
854 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #403 background imageLoading...
Page #403 background image
12-19
Cisco 10000 Series Router Quality of Service Configuration Guide
OL-7433-09
Chapter 12 Sharing Bandwidth Fairly During Congestion
Configuration Examples for Sharing Bandwidth Fairly
Configuration Example for Configuring CBWFQ and Attaching a Policy to an
ATM Subinterface
Example 12-6 shows how to configure CBWFQ in a policy map and attach the policy to an ATM
subinterface. This example creates a class map named voice to classify traffic and assigns class
characteristics in the policy map named policy1. The service policy is applied to the ATM
subinterface
7/0/0.1, which uses PPPoA encapsulation.
Example 12-6 Configuring CBWFQ and Attaching a Policy to a PPPoA Subinterface
Router(config)# class-map voice
Router(config-cmap)# match any
Router(config-cmap)# exit
Router(config)# policy-map policy1
Router(config-pmap)# class voice
Router(config-pmap-c)# police 120000 16000 32000 conform-action transmit exceed-action
set-prec-transmit 4
Router(config-pmap-c)# exit
Router(config-pmap)# exit
Router(config)# interface atm7/0/0.1 point-to-point
Router(config-subif)# pvc 10/32
Router(config-subif-atm-pvc)# encapsulation aal5mux ppp virtual-template 1
Router(config-subif-atm-pvc)# service-policy output policy1
Router(config-subif)# interface virtual-template 1
Router(config-if)# ip unnumbered loopback1
Router(config-if)# peer default ip address pool pool1
Router(config-if)# ppp authentication chap
Configuration Example for Configuring CBWFQ and Attaching a Policy to an
RBE Subinterface
Example 12-7 shows how to configure CBWFQ in a policy map and attach the policy to an routed bridge
encapsulation (RBE) subinterface. The example creates a class map named voice and a policy map
named map1. The service policy is applied to the ATM subinterface 7/0/1.1, which uses ATM RBE.
Example 12-7 Configuring CBWFQ and Attaching a Policy to an RBE Subinterface
Router(config)# class-map voice
Router(config-cmap)# match all
Router(config-cmap)# exit
Router(config)# policy-map map1
Router(config-pmap)# class voice
Router(config-pmap-c)# police 120000 16000 32000 conform-action transmit exceed-action set
precedence-transmit 4
Router(config-pmap-c)# exit
Router(config-pmap)# exit
Router(config-if)# interface atm7/0/1.1 point-to-point
Router(config-subif)# ip unnumbered loopback1
Router(config-subif)# atm route-bridge ip
Router(config-subif)# service-policy output map1
Router(config-subif)# range pvc 101/32 101/2031
Router(config-subif-atm-pvc)# encapsulation aal5snap

Table of Contents

Other manuals for Cisco 10000 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 10000 Series and is the answer not in the manual?

Cisco 10000 Series Specifications

General IconGeneral
BrandCisco
Model10000 Series
CategoryNetwork Router
LanguageEnglish

Related product manuals