Fujitsu N7100 User Manual

4.18 Setting a Job Sequence
201
■ Splitting an Output File
An output file can be split in the following ways for a job sequence:
 Specifying a number of pages
 Using a patch code sheet
This function allows you to split a file in a specified unit of pages without stopping a scan
when scanning more than one document. A file is split in a specified unit of pages, and
consequently the scanned images are separated into each scanned document (unit of
pages that is split).
This function can only be set for a job sequence. To set this function, select [Separation]
in [Save] in [Scan Settings].
 Specifying a number of pages
To specify a number of pages, select [Number of pages] for [Separation Mode].
Using this setting splits a file in pages determined by the number of pages you specify.
When the last split file is output, if the number of pages that is output is less than the
number of pages you specify, the output file contains the last output pages.
Additional scanned pages are not recognized as an additional batch and instead of
this, all pages including additional pages are recognized as a batch, then split.
 Using patch codes
To set patch codes, select [Patch Code] for [Separation Mode].
Using this setting, and scanning documents with patch code sheets inserted into the
points where documents are to be separated, a file is split and output in the specified
unit of pages.
You can configure the setting for naming split output files.
Separator string, document counter, and page counter (for a single page) with delimiters
(hyphens "-") are appended to the existing file naming rule.
Examples of file names are as follows:
 Separator
Examples: File naming rule (user name with a sequence number), no separator string
specified, PDF
Guest0001-SEPARATOR0001.pdf
Guest0001-SEPARATOR0002.pdf
 Document Counter
Examples: File naming rule (user name without a sequence number), JPG (Since the
files are single-page files, a sequence number for the page counter is appended.)
Guest-0001-00001.jpg
Guest-0001-00002.jpg
Guest-0001-00003.jpg
Guest-0002-00001.jpg
Guest-0002-00002.jpg
 Separator and Document Counter
Examples: File naming rule (user name with a sequence number), separator string
(scanner) specified, PDF
Guest0001-scanner-0001.pdf
Guest0001-scanner-0002.pdf

Fujitsu N7100 Specifications

General

Film scanning	No
Color scanning	Yes
Input color depth	- bit
Maximum scan size	216 x 3048 mm
Output color depth	24 bit
ADF scan speed (b/w, A4)	25 ppm
Optical scanning resolution	600 x 600 DPI
Duplex ADF scan speed (b/w, A4)	50 ipm
Black/white scanning color modes	Grayscale, Monochrome
Display	LCD
Scanner type	ADF scanner
Product color	Black
Display diagonal	8.4 \
Display resolution	1024 x 768 pixels
Scan to	E-mail, E-mail Server, Fax, File, FTP
Sensor type	CIS
Scan file formats	JPG, PDF, TIFF
Daily duty cycle (max)	400 pages
Supported network protocols	TCP/IP(IPv4 / IPv6), DNS, DHCP, SMTP, SMB, LDAP, NTP, FTP, HTTP, SNMP
Auto document feeder (ADF) input capacity	50 sheets
Maximum scan area (ADF)	216 x 355.6 mm
Minimum scan area (ADF)	50.8 x 50.8 mm
ISO A-series sizes (A0...A9)	A4, A5, A6, A8
ISO B-series sizes (B0...B9)	B5, B6
Scanning media types supported	Business Card, Plain paper, Plastic Card, Post Card(JPN), Thick paper, Thin paper
Maximum ISO A-series paper size	A4
Auto Document Feeder (ADF) media weight	40 - 209 g/m²
USB version	2.0
Standard interfaces	Ethernet, USB 1.1, USB 2.0
Input voltage	100-240 V
Power supply type	AC
AC input frequency	50 - 60 Hz
Power consumption (standby)	1 W
Power consumption (typical)	38 W
Power consumption (PowerSave)	2 W
Operating temperature (T-T)	5 - 35 °C
Operating relative humidity (H-H)	20 - 80 %
Sustainability certificates	RoHS, ENERGY STAR
Bundled software	Scanner Central Admin Server
Ethernet LAN data rates	10, 100, 1000 Mbit/s

Weight and Dimensions

Depth	232 mm
Width	300 mm
Height	172 mm
Weight	6000 g