Fujitsu N7100 User Manual

D.5 Barcode Types and Detection Conditions
427
Narrow element
width/module width
 UPC-A/EAN/JAN
300 dpi or more: 0.264 mm/0.010 in. or wider
Less than 300 dpi: 0.30 mm/0.012 in. or wider
 CODE39/CODE128/EAN128/Codabar (NW7)
300 dpi or more: 0.20 mm/0.008 in. or wider
Less than 300 dpi: 0.30 mm/0.012 in. or wider
 ITF
300 dpi or more: 0.254 mm/0.010 in. or wider
Less than 300 dpi: 0.30 mm/0.012 in. or wider
Wide element width 14 mm/0.55 in. or less
(For UPC-A/EAN/JAN/CODE128/EAN128, this is the widest
element width (corresponds to 4 modules).)
Inter-character gap  UPC-A/EAN/JAN/CODE128/EAN128/ITF
No inter-character gap exists.
 CODE39/Codabar (NW7)
(Equal to or wider than the narrow element width, and
equal to or less than 1.52 mm/0.06 in. or 3 times of the
narrow element width, whichever wider)
ATTENTION
 Skewed barcodes may not be recognized correctly.
 Using the same sheet repeatedly may decrease the recognition accuracy due to
accumulated dirt on the sheets. If the sheet is not recognized correctly or gets smudged,
replace it with a new sheet.
 If recognition of control codes fails, it may cause the following results:
 Control codes are recognized as numerical characters.
 Not only the control codes but part of other characters are not recognized and ignored.
 When control code [NUL] is included in a barcode, it is replaced with " " (space).
 When documents to be scanned are skewed or printed barcodes are not in a good condition,
barcodes on the document may not be recognized correctly.
 If more than one barcode exists in the recognition area, it becomes unknown which one will
be effective.
 If more than one barcode exists in the recognition area, it becomes unknown that which one
will be recognized first.
 Barcodes may be recognized even when the barcode is not black or its background color is
not white. To make color barcodes recognizable, you first need to configure the settings for
scanning colored documents and check that recognition works properly.
HINT
 The recommended image resolution is 200 to 600 dpi.
 When barcodes are used and the scan speed slows down, reducing the number of barcode
types to be selected may improve the scan speed.
Item Conditions

Fujitsu N7100 Specifications

General

Film scanning	No
Color scanning	Yes
Input color depth	- bit
Maximum scan size	216 x 3048 mm
Output color depth	24 bit
ADF scan speed (b/w, A4)	25 ppm
Optical scanning resolution	600 x 600 DPI
Duplex ADF scan speed (b/w, A4)	50 ipm
Black/white scanning color modes	Grayscale, Monochrome
Display	LCD
Scanner type	ADF scanner
Product color	Black
Display diagonal	8.4 \
Display resolution	1024 x 768 pixels
Scan to	E-mail, E-mail Server, Fax, File, FTP
Sensor type	CIS
Scan file formats	JPG, PDF, TIFF
Daily duty cycle (max)	400 pages
Supported network protocols	TCP/IP(IPv4 / IPv6), DNS, DHCP, SMTP, SMB, LDAP, NTP, FTP, HTTP, SNMP
Auto document feeder (ADF) input capacity	50 sheets
Maximum scan area (ADF)	216 x 355.6 mm
Minimum scan area (ADF)	50.8 x 50.8 mm
ISO A-series sizes (A0...A9)	A4, A5, A6, A8
ISO B-series sizes (B0...B9)	B5, B6
Scanning media types supported	Business Card, Plain paper, Plastic Card, Post Card(JPN), Thick paper, Thin paper
Maximum ISO A-series paper size	A4
Auto Document Feeder (ADF) media weight	40 - 209 g/m²
USB version	2.0
Standard interfaces	Ethernet, USB 1.1, USB 2.0
Input voltage	100-240 V
Power supply type	AC
AC input frequency	50 - 60 Hz
Power consumption (standby)	1 W
Power consumption (typical)	38 W
Power consumption (PowerSave)	2 W
Operating temperature (T-T)	5 - 35 °C
Operating relative humidity (H-H)	20 - 80 %
Sustainability certificates	RoHS, ENERGY STAR
Bundled software	Scanner Central Admin Server
Ethernet LAN data rates	10, 100, 1000 Mbit/s

Weight and Dimensions

Depth	232 mm
Width	300 mm
Height	172 mm
Weight	6000 g