Fujitsu N7100 User Manual

4.6 Configuring the Login-Related Settings
93
2. For [Authentication Mode], select an authentication mode.
3. For [Auto Login], select whether or not to enable automatic login.
4. When [Auto Login] is set to [Yes], enter a [User Name] and [Password].
The scanner follows the Active Directory user name format when authenticating the
user login.
 For users registered in the LDAP server
 When the [Server Type] of the LDAP server is [Active Directory] or [Active
Directory Global Catalog]
HINT
When an alias is used for the administrator account, if a local account or LDAP user is
set with the same alias account name, login will be processed for the administrator
account. In this case, even if a password error occurs, login as a local account or LDAP
user cannot be performed.
The priority of the authentication destinations for the login is as follows:
1. Alias account
2. Order specified by [Authentication Mode]
ATTENTION
 The automatic login setting is applied immediately after an administrator logout. To
change the settings while the [Auto Login] is [ON], perform administrator login from the
[Maintenance] window or perform the login via the Admin Tool.
 If Central Admin is enabled in a scanner for which automatic login is enabled, when the
scanner is started or resumed from standby mode, preference is given to checking for
available scanner settings, add-in installs and system settings in the Central Admin
Server, over automatic login.
When scanner settings, Add-ins or system settings are available, they are installed in
the scanner. If the number of scanners connecting to the Central Admin Server exceeds
the maximum acceptable number, the installation is skipped, and automatic login is
performed.
Updates will be applied to the scanner when a logout is performed from the
[Administrator Login] window, when the scanner starts next time, or when the scanner
resumes from standby mode.
User Name Format Authentication Process
SAM Account Name
Does not contain @
Authenticate the user login name
(sAMAccountName).
Example: user
User Principal Name
Contains @
Authenticate the user login name
(userPrincipalName).
Example: user@example.com
HINT
When specifying a SAM account name with a domain name, describe
"domain_name\SAM_account_name".

Fujitsu N7100 Specifications

General

Film scanning	No
Color scanning	Yes
Input color depth	- bit
Maximum scan size	216 x 3048 mm
Output color depth	24 bit
ADF scan speed (b/w, A4)	25 ppm
Optical scanning resolution	600 x 600 DPI
Duplex ADF scan speed (b/w, A4)	50 ipm
Black/white scanning color modes	Grayscale, Monochrome
Display	LCD
Scanner type	ADF scanner
Product color	Black
Display diagonal	8.4 \
Display resolution	1024 x 768 pixels
Scan to	E-mail, E-mail Server, Fax, File, FTP
Sensor type	CIS
Scan file formats	JPG, PDF, TIFF
Daily duty cycle (max)	400 pages
Supported network protocols	TCP/IP(IPv4 / IPv6), DNS, DHCP, SMTP, SMB, LDAP, NTP, FTP, HTTP, SNMP
Auto document feeder (ADF) input capacity	50 sheets
Maximum scan area (ADF)	216 x 355.6 mm
Minimum scan area (ADF)	50.8 x 50.8 mm
ISO A-series sizes (A0...A9)	A4, A5, A6, A8
ISO B-series sizes (B0...B9)	B5, B6
Scanning media types supported	Business Card, Plain paper, Plastic Card, Post Card(JPN), Thick paper, Thin paper
Maximum ISO A-series paper size	A4
Auto Document Feeder (ADF) media weight	40 - 209 g/m²
USB version	2.0
Standard interfaces	Ethernet, USB 1.1, USB 2.0
Input voltage	100-240 V
Power supply type	AC
AC input frequency	50 - 60 Hz
Power consumption (standby)	1 W
Power consumption (typical)	38 W
Power consumption (PowerSave)	2 W
Operating temperature (T-T)	5 - 35 °C
Operating relative humidity (H-H)	20 - 80 %
Sustainability certificates	RoHS, ENERGY STAR
Bundled software	Scanner Central Admin Server
Ethernet LAN data rates	10, 100, 1000 Mbit/s

Weight and Dimensions

Depth	232 mm
Width	300 mm
Height	172 mm
Weight	6000 g