Simplex 4100ES - Page 18

18
Figure 4-12. Wired Media Interconnections Between 4100ES Motherboards .................. 4-16
Figure 4-13. Modem Wiring............................................................................................... 4-17
Figure 4-14. Wired Media, Style 7 Wiring ......................................................................... 4-18
Figure 4-15. Fiber Optic, Style 7 Wiring............................................................................ 4-19
Figure 4-16. Wired Media and Fiber Optic, Style 7 Wiring................................................ 4-20
Figure 4-17. Modem Media Wiring (Non-4100ES/4100U Only)........................................ 4-21
Figure 4-18. Network Audio Riser Controller Module........................................................ 4-22
Figure 4-19. Analog Audio Interconnections..................................................................... 4-24
Figure 4-20. Digital Audio Interconnections (4100-1311 Digital Audio Controller)............ 4-25
Figure 4-21. Distributed Microphone Interconnections ..................................................... 4-26
Figure 4-22. Installing a Digital Audio PDI Termination Plug ............................................ 4-27
Figure 6-1. Power-Limited Wiring......................................................................................... 6-3
Figure 6-2. The EOL Relay................................................................................................. 6-4
Figure 6-3. Class A NAC Wiring.......................................................................................... 6-8
Figure 6-4. Class B Wiring .................................................................................................. 6-9
Figure 6-5. Loop Wiring as Shown.................................................................................... 6-10
Figure 6-6 . Class A Wiring............................................................................................... 6-11
Figure 6-7. Class B Wiring ................................................................................................ 6-12
Figure 6-8. Auxiliary Power Wiring.................................................................................... 6-14
Figure 6-9. Auxiliary Relay Wiring..................................................................................... 6-15
Figure 7-1. EPS Card Layout.............................................................................................. 7-2
Figure 7-2. DIP Switch SW2 ............................................................................................... 7-3
Figure 7-3. Earth Connect Jumper Positions ...................................................................... 7-4
Figure 7-4. Battery Disconnect Jumper Positions............................................................... 7-4
Figure 7-5. DIP Switch SW1 ............................................................................................... 7-5
Figure 7-6. PDM/Battery Connections ................................................................................ 7-6
Figure 7-7. LED Location.................................................................................................... 7-7
Figure 8-1. Power-Limited Wiring Guidelines...................................................................... 8-2
Figure 8-2. Ferrite Bead Installation.................................................................................... 8-4
Figure 8-3. Class B Wiring .................................................................................................. 8-7
Figure 8-4. Class B Wiring With Isolators ........................................................................... 8-8
Figure 8-5. AUX/NAC Terminal........................................................................................... 8-9
Figure 8-6. Simple NAC Wiring........................................................................................... 8-9
Figure 8-7. Class A Jumper Setting .................................................................................. 8-11
Figure 8-8. IDNet 2 Class A Wiring................................................................................... 8-11
Figure 8-9. Class B Jumper Setting .................................................................................. 8-12
Figure 8-10. IDNet 2 Class B Wiring................................................................................. 8-12
Figure 9-1. Service and Diagnostic Interface....................................................................... 9-2
Figure 9-2. Data Transfer Interface..................................................................................... 9-2
Figure 9-3. Bootloader Interface ......................................................................................... 9-3
Figure 9-4. CPU card ports................................................................................................. 9-4
Figure 9-5. Front Panel Ethernet Service Port.................................................................... 9-4
Figure 10-1. Supervisory and Trouble LEDs for both MNS and Fire ................................. 10-5
Figure 10-2. Voice Message Configuration Example........................................................ 10-6
Figure A-1. DIP Switch SWx................................................................................................A-1
Figure B-1. Master Controller Bay (4100)............................................................................B-2
Figure B-2. UT Motherboard (565-161)............................................................................... B-3
Figure B-3. UT Motherboard with City Connection (565-213)............................................. B-3
Figure B-4. UT Motherboard with City Connection (565-274)............................................. B-3
Figure B-5. UT Master Controller (565-333) ....................................................................... B-4
Figure B-6. UT Master Controller (565-148) ....................................................................... B-4
Figure B-7. Universal Power Supply................................................................................... B-5
Figure B-8. Operator Interface............................................................................................ B-6
Figure B-9. Master Controller and Expansion Bays............................................................ B-6
Figure B-10. Power and Comm Lines................................................................................. B-7
Figure B-11. Back Box Installation Diagram ....................................................................... B-9
Figure B-12. Removing the Shipping Studs...................................................................... B-10
Figure B-13. Inserting the Mounting Screws..................................................................... B-11
Figure B-14. Installing the System Electronics Bay Assembly.......................................... B-12
Figure B-15. Master Controller Bay Interconnections....................................................... B-17
Figure B-16. Installing the Motherboard in an Expansion Bay.......................................... B-18
Figure B-17. Power and Communication Wiring for Motherboards................................... B-20
Figure C-1. MINIPLEX System Design................................................................................C-3
List of Figures