Honeywell HC900 Reference Guide

x HC900 Hybrid Control Designer Function Block Reference Guide Revision 11
2/07
HTable 55 HOA feedback signal tab parameters....................................................................................................... H174
HTable 56 Lead lag configuration parameters........................................................................................................... H180
HTable 57 Low monitor function block configuration parameters............................................................................ H183
HTable 58 Math function block configuration parameters ........................................................................................ H191
HTable 59 MBR function block configuration parameters........................................................................................ H194
HTable 60 MBS Block General tab configuration parameters .................................................................................. H198
HTable 61 MBS Block Read tab configuration parameters........................................................................................ H199
HTable 62 MBS Block Write tab configuration parameters....................................................................................... H201
HTable 63 MBW function block configuration parameters....................................................................................... H205
HTable 64 Min/Max/Ave/Sum function block configuration parameters ................................................................. H214
HTable 65 Mass flow function block configuration parameters................................................................................ H217
HTable 66 On delay timer function block example ................................................................................................... H226
HTable 67 Off delay timer configuration parameters ................................................................................................ H229
HTable 68 ON/OFF General tab configuration parameters ........................................................................................ H234
HTable 69 ON/OFF Start/Restart tab configuration parameter .................................................................................. H236
HTable 70 ON/OFF RSP tab configuration parameters.............................................................................................. H237
HTable 71 ON/OFF Range/limit tab configuration parameters.................................................................................. H239
HTable 72 ON/OFF Alarm tab configuration parameters.......................................................................................... H241
HTable 73 Pushbutton function group configuration................................................................................................. H251
HTable 74 PDE General tab configuration parameters.............................................................................................. H255
HTable 75 PDE Read tab configuration parameters .................................................................................................. H256
HTable 76 PDE Write tab configuration parameters ................................................................................................. H257
HTable 77 Pulse Input Configuration Parameters....................................................................................................... H264
HTable 78 Pulse Output Configuration Parameters.................................................................................................... H267
HTable 79 PID General tab configuration parameters............................................................................................... H273
HTable 80 PID Start/Restart tab configuration parameter ......................................................................................... H275
HTable 81 PID RSP tab configuration parameters .................................................................................................... H277
HTable 82 PID Range/limit tab configuration parameters......................................................................................... H279
HTable 83 PID Tuning tab configuration parameters................................................................................................ H281
HTable 84 PID Accutune III tab configuration parameters ....................................................................................... H282
HTable 85 PID Alarms tab configuration parameters................................................................................................ H286
HTable 86 Position Proportional Motor Control ........................................................................................................ H294
HTable 87 PT function block configuration parameters............................................................................................ H298
HTable 88 QDT parameters....................................................................................................................................... H301
HTable 89 Analog Input with Remote C/J configuration parameters........................................................................ H304
HTable 90 HC900 Input Types and Ranges for RAI Function Block ....................................................................... H306
HTable 91 RAMP general tab parameters ................................................................................................................. H313
HTable 92 RAMP tabs parameters ............................................................................................................................ H314
HTable 93 Read constant configuration data ............................................................................................................. H317
HTable 94 Metric units .............................................................................................................................................. H321
HTable 95 ROC configuration parameters ................................................................................................................ H323
HTable 96 Redundancy Status configuration parameters .......................................................................................... H325
HTable 97 RTMR configuration parameters ............................................................................................................. H331
HTable 98 SCB configuration parameters ................................................................................................................. H334
HTable 99 SPP inputs and current state..................................................................................................................... H346
HTable 100 Restart scenario options ......................................................................................................................... H346
HTable 101 SPP configuration parameters ................................................................................................................ H347
HTable 102 Tag/Failsafe configuration parameters................................................................................................... H355
HTable 103 Main Output labels configuration parameters........................................................................................ H356
HTable 104 Auxiliary Output labels configuration parameters ................................................................................. H357
HTable 105 Event labels configuration parameters ................................................................................................... H358
HTable 106 SQRT configuration parameters ............................................................................................................ H363
HTable 107 STG general tab parameters ................................................................................................................... H366
HTable 108 Default PV sources and compare type operators.................................................................................... H368
HTable 109 STG Stage Tabs parameters................................................................................................................... H369

Honeywell HC900 Specifications

General

Series	HC900
Redundancy	Optional
Programming Language	Function Block Diagram, Ladder Logic, Structured Text
Inputs	Analog, Digital
Outputs	Analog, Digital, Relay
Display	Optional
Control	PID, Advanced Control
Power Supply	24V DC or 100-240V AC
Storage Temperature	-40°C to 85°C
Humidity	5% to 95% non-condensing
Communication Protocols	Modbus, Ethernet