Table of Contents
CCD CAM 100 – Installation and Operating Manual v
8.9.7 Y Axis Alignment ......................................................................................................... 94
8.9.8 Measuring Range Setting............................................................................................ 95
8.9.9 Focus Setting............................................................................................................... 96
8.9.10 Z Axis Alignment.......................................................................................................... 98
8.10 Setting the Aperture ................................................................................................. 102
8.11 Carrying Out White Balance...................................................................................... 103
8.12 Carrying Out Scaling.................................................................................................. 104
8.13 Calibrating the CCD Camera...................................................................................... 107
8.13.1 Calibration Template ................................................................................................ 107
8.13.2 Inserting the Calibration Template ........................................................................... 108
8.13.3 Calibrating the CCD Camera...................................................................................... 109
8.14 Performing a Material Thickness Compensation ...................................................... 110
9 Operation ......................................................................................................112
9.1 Safety Instructions .................................................................................................... 112
9.2 Starting the System................................................................................................... 113
9.3 Opening the Service Opening ................................................................................... 114
9.4 Inserting/Removing the Memory Card ..................................................................... 115
9.5 Menu Navigation ...................................................................................................... 116
9.5.1 Menu Structure......................................................................................................... 116
9.5.2 Path Details............................................................................................................... 116
9.5.3 Opening a Menu ....................................................................................................... 117
9.6 Operation Display ..................................................................................................... 119
9.6.1 Overview................................................................................................................... 119
9.6.2 Display of CAN Bus Information................................................................................ 120
9.6.3 Display of the Data Transfer Rate ............................................................................. 121
9.6.4 Display of the Operating Mode and Sensor Resolution............................................ 121
9.6.5 Error Display.............................................................................................................. 121
9.6.6 Display of the Exposure Settings............................................................................... 121
9.6.7 Display of the Set Aperture Value............................................................................. 122
9.6.8 Display of the Unit for the Output of the Measured Values..................................... 122
9.6.9 Calling Up the System Menus ................................................................................... 122
9.6.10 Display of the Video Curve........................................................................................ 123
9.7 Camera Setup Menu ................................................................................................. 123
9.8 Application Settings Menu........................................................................................ 124
9.8.1 Menu Structure......................................................................................................... 125
9.8.2 Setting the Aperture, Focus and Exposure Time....................................................... 126
9.8.3 Defining the Exposure Settings ................................................................................. 129
9.8.4 Setting the Measuring Range and Focus................................................................... 133
9.8.5 Defining the Edges .................................................................................................... 134
9.8.6 Defining the Edge Detection Area............................................................................. 140
9.8.7 Defining the Edge Detection Sensitivity.................................................................... 143
9.8.8 Defining the Scan Direction ...................................................................................... 145
9.8.9 Setting the Material Distance ................................................................................... 148
9.8.10 Adjusting the Material Thickness.............................................................................. 148
9.8.11 Carrying Out White Balance...................................................................................... 149
9.9 Device Settings Menu ............................................................................................... 149
9.9.1 Menu Structure......................................................................................................... 150
9.9.2 Setting the IP Address............................................................................................... 151
9.9.3 Setting the Netmask ................................................................................................. 151
9.9.4 Showing the MAC Address........................................................................................ 152
9.9.5 Selecting the Synchronization Method..................................................................... 152
9.9.6 Setting the CAN Bus Address .................................................................................... 153
9.9.7 Activating the CAN Bus Terminating Resistor ........................................................... 155
9.9.8 Selecting the Calibration Method ............................................................................. 156
9.9.9 Setting the Calibration Constant............................................................................... 157
9.9.10 Setting the Distance of the CCD Camera to the Material ......................................... 157
9.9.11 Rotating the Screen Display...................................................................................... 158
9.9.12 Locking the Touchscreen .......................................................................................... 159
To Next Page
Loading...
Need help?
General
