Cisco ASR 1000 Series Software Configuration Guide

, 0 frame, 0 overrun, 0 ignored
0 watchdog, 1670 multicast, 0 pause input
1715 packets output, 656528 bytes, 0 underruns
0 output errors, 0 collisions
, 4 interface resets
0 babbles, 0 late collision
, 0 deferred
0 lost carrier, 0 no carrier
, 0 pause output
0 output buffer failures, 0 output buffers swapped out
Router# show interfaces tengigabitethernet 0/0/0
TenGigabitEthernet7/0/0 is up, line protocol is up (connected)
Hardware is TenGigEther SPA, address is 0000.0c00.0102 (bia 000f.342f.c340)
Internet address is 15.1.1.2/24
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not supported
Full-duplex, 10Gb/s
input flow-control is on, output flow-control is on
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:10, output hang never
Last clearing of "show interface" counters 20:24:30
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
L2 Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes
L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcast
L3 out Switched: ucast: 0 pkt, 0 bytes mcast: 0 pkt, 0 bytes
237450882 packets input, 15340005588 bytes, 0 no buffer
Received 25 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC
, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
1676 packets output, 198290 bytes, 0 underruns
0 output errors, 0 collisions
, 4 interface resets
0 babbles, 0 late collision
, 0 deferred
0 lost carrier, 0 no carrier
, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
To verify that your interface is operating properly, complete the following steps:
SUMMARY STEPS
1.
From global configuration mode, enter the show interfaces gigabitethernet, show interfaces
tengigabitethernet, or show interfaces fastethernet command.
2.
Verify that the interface is up.
3.
Verify that the line protocol is up.
4.
Observe the CRC counter.
5.
Observe the carrier signal counters.
DETAILED STEPS
Step 1
From global configuration mode, enter the show interfaces gigabitethernet, show interfaces tengigabitethernet, or
show interfaces fastethernet command.
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide, Cisco IOS XE
Everest 16.5
OL-14127-17 177
Troubleshooting the Gigabit Ethernet SPAs
Performing Basic Interface Troubleshooting

Cisco ASR 1000 Series Specifications

General

Brand	Cisco
Model	ASR 1000 Series
Category	Network Router
Language	English