Upgrade and Maintenance Manual
RX200 S8
Contents
6.5.2 Removing the defective power distribution board . . . . . . . . 102
6.5.3 Installing the new power distribution board . . . . . . . . . . . 103
6.5.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 105
7 Hard disk drives / solid state drives . . . . . . . . . . . . . 107
7.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 108
7.1.1 General equipping rules . . . . . . . . . . . . . . . . . . . . 108
7.1.2 Configuration with up to four HDD/SSD modules . . . . . . . . 109
7.1.3 Configuration with up to eight HDD/SSD modules . . . . . . . 109
7.2 Installing a 2.5-inch HDD/SSD module . . . . . . . . . . . . 110
7.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 110
7.2.2 Removing the 2.5-inch dummy module . . . . . . . . . . . . . 111
7.2.3 Installing the 2.5-inch HDD/SSD module . . . . . . . . . . . . 112
7.2.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 113
7.3 Removing a 2.5-inch HDD/SSD module . . . . . . . . . . . 113
7.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 113
7.3.2 Removing the 2.5-inch HDD/SSD module . . . . . . . . . . . 114
7.3.3 Installing the 2.5-inch dummy module . . . . . . . . . . . . . 115
7.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 115
7.4 Replacing a 2.5-inch HDD/SSD module . . . . . . . . . . . 115
7.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 116
7.4.2 Removing the defective 2.5-inch HDD/SSD module . . . . . . 116
7.4.3 Installing the new 2.5-inch HDD/SSD module . . . . . . . . . 116
7.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 116
7.5 Replacing the 4xHDD backplane . . . . . . . . . . . . . . . 117
7.5.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 117
7.5.2 Removing the defective 4xHDD backplane . . . . . . . . . . . 117
7.5.3 Installing the new 4xHDD backplane . . . . . . . . . . . . . . 119
7.5.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 120
7.6 Replacing the 8xHDD backplane . . . . . . . . . . . . . . . 120
7.6.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 120
7.6.2 Removing the defective 8xHDD backplane . . . . . . . . . . . 121
7.6.3 Installing the new 8xHDD backplane . . . . . . . . . . . . . . 123
7.6.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 124
7.7 Converting to configuration up to eight HDD/SSD modules 125
7.7.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 125
7.7.2 Removing the 4xHDD backplane and the ODD cage . . . . . . 125
To Next Page
Loading...
