117
Program operating mode
Page 12 - Amp
PAGE 12 - AMP
These parameters control the volume and pan of the
selectedoscillator.
Selected
Usethisparametertoselectanoscillatortoputinedit.
Alternatively,youcanselectoscillatorsusingtheF‐1–F‐
4buttons.
Level
Volumeoftheselectedoscillator.
Note:Thevolumeofa Programcan becontrolledby CC#7
(volume) and #1
1(expression).The resultinglevel isdeter‐
mined by multiplying the values of CC#
7 and #11. The
GlobalMIDIchannelisusedforcontrol.
0…127 Volumelevel.
Pan
Pan(stereo position)oftheselectedoscillator.
This parameter is not available when editing a Drum
Program. Use the
individual Pan contr
ol for each key
(see“Pan”onpage109).
Random The sound will be heard from a different
locati
onateachnote‐on.
L001 Placesthesoundatfarleft.
C064 Placesthesoun
dinthecenter.
R127 Placesthesoun
dtofarright.
Note:ThiscanbecontrolledbyCC
#10(panpot). ACC#10
valueof0or1willpl
acethesoundatthefarleft,avalueof
64willplacethesoundatthelocationspecifiedby the“Pan”
settingforeachoscillator, anda value of 127 will place the
soundatth
efarright. ThisiscontrolledontheglobalMIDI
channe
l.
Pan modulation
AMS (Alternate Modulation Source)
Selects the source that will modify pan (see “A M S
(Alternate Modulation Source) list” on page12
3).This
changewillberelativetothe“Pan”setting.
Intensity
Specifies the depth of the effect produced by “AMS ”.
Forexample,if“Pan”issettoC064 and“A M S ” isNote
Number, positive (+) values of this parameter will
cause the sound to movetoward the right as the note
numbersincreasebeyondtheC4note(i.e.,asyouplay
higher), and tow
ard the left as the note numbers
decrease(i
.e.,asyouplaylower).Negative(–)valuesof
thisparameterwillhavetheoppositeeffect.
‐99…+99 Parametervalue.
PAGE 13 - AMP MODULATION
These settings allow youtoapply modulation to amp
(foreachoscillator)tomodulatethevolume.
Selected
Usethisparametertoselectanoscillatortoputinedit.
Alternatively,youcanselectoscillatorsusingtheF‐1–F‐
4buttons.
Amplifier keyboard tracking
Theseparametersletyouusekeyboardtrackingtoadjust
thevolumeoftheselectedoscillator.Usethe“Key”and
“Ramp” parameters to specify how the volume will be
affectedbythekeyboardlocationthatyouplay.
Tracking Low/High
These settings specify the note number at which key‐
boardtrackingwillbegintoapply.Thevolu
mewillnot
changebetween“TrackingLow”and“TrackingHigh ” .
C–1…G9 Lowe
st/Highestnoteintherange.
Tracking Low
Keyboard tracking will apply to the range below the
specifiednotenumber.
Tracking High
Keyboard tracking will apply to the range above the
specifiednotenumber.
Ramp
Theseparametersspecify theangleofkeyboardtrack‐
ing.
‐99…+99 Anglevalue.
Here is an ex
ample of volum
e changes produced by
keyboardlocationand“Ramp”settings:
Ramp Low
Withpositive (+) values of this parameter, the volume
will increase as you play notes below the “Tracking
Low” note number. With negative (–) va
lues, the vol‐
umewilldecrease.
Ramp High
Withpositive (+) values of this parameter, the volume
willincreaseas youplay notes above the “Key High”
notenumber.Withnegative(–)values,thevolumewill
decrease.
Volume
Key
Ramp Low=+99
Ramp Low=0
Ramp Low=–99
Ramp High=+99
Ramp High=0
Ramp High=–99
Key Low
Key High
To Next Page
Loading...
Need help?
General
