107
Program operating mode
Page 1 - Basic
PAGE 1 - BASIC
HereyoucanmakebasicsettingsfortheProgram,such
asbasicoscillatorsettings,theoscillatorcount,andthe
polyphonicmode.
Oscillators
Use this parameter to specify the basicProgramtype;
whetheritwilluseoneormoreoscillators(uptofour).
DrumProgramsuseonlyoneoscillator.
1…4
Number of oscillators the Program will
use.Thetotalamountofpolyphonyva
ries
depending on the number of oscillators
used by the Program (a maximum of 62
withonly1oscillator,oramaximumof15
with4oscillators).
Mode
ThisisthepolyphonicmodeoftheProgram.
Poly The Program will play polyphonically,
allowingyo
uplaychords.
Mono The Program will play monophonically,
producingonlyonenoteatatime.
Single Trigger
Thisparameterisavailablewhenthe“Mode”parame‐
terissettoPoly.
Yes W
henthesamenote isplayedrepeatedly,
the previou
s note will be silenced before
thenextnoteissounded,sothatthenotes
donotoverlap.
No Whenthesamenoteisplayedrepeatedly,
the previou
s note will not be silenced
beforethenextnoteissounded.
Legato
Thisparameterisavailablewhenthe“Mode”parame‐
terissettoMono.
Yes Legato is on. When
multiple note‐on’s
occur, the fi
rst note‐on will retrigger the
sound, and the second and subsequent
note‐on’swillnotretrigger.
Whenlegatoison,multiplenote‐on’swill
not retrigger the voice. If one note is
alreadyonandanothernoteisturnedon,
thefirstvoicewillcontinuesounding.The
oscillator sound, envelope, and LFO will
not be reset, and only the pitch of the
oscillator will be updated. This set
ting is
effectiveforwindins
trumentsoundsand
analogsynth‐typesounds.
No Legatoisoff.Noteswillalways be retri
g‐
geredwhennote‐onoccurs.
Whenlegatoisoff,multiplenote‐on’
swill
re
trigger the voice at each note‐on. The
oscillator sound, envelope, and LFO will
bereset(andretriggered)accordingtothe
settingsoftheProgram.
Note: If“Legato” is On, certain multisample
s or keyboard
locationsmayproduceanincorrectpitch.
Priority
Thisparameterisavailablewhenthe“Mode”parame‐
terissettoMono.Itspecifieswhichnotewill
begiven
priority to play when two or more notes are played
simultaneously.
Low Lowestnotewilltakepriority.
High Highestnotewilltakepriority
.
Last
Lastnotewilltakepriority.
PAGE 2 - SAMPLE (SOUND PROGRAMS)
Themultisample(s)(waveform)onwhichtheProgram
willbe based canbeselectedhere foreachofthe four
oscillators.Eachoscillatorcanuse1or2multisamples,
eachoneassignedtotheHighorLowlayer.
The internal Flash‐ROM contains 340 different multi‐
samples(presetmultisamples).
Selected
Usethisparametertoselectanoscillatortoputinedit.
Alternatively,youcanselectoscillatorsusingtheF‐1–F‐
4buttons.
MS Hi/Lo Bank/Num
Usethese parameterstoselectadifferentmultisample
foreachoftheHighandLowlayers.Youcanuseveloc‐
ity to switch between the two multisamples. Reve
rse,
OffsetandLevelcanbeadjustedindependentlyforthe
HighandLowmultisamples.
Thefirstlineshowsthebank(ROM),whilethese
cond
line is for selecting the multisample. The Program
numberappearsattheendofthesecondline.
The multisample you selectfor the High laye
r will be
triggered by velocities higher than the value of the
“Velocity Switch” parameter (see page108). If you do
not wish to use ve
locity switching ,settheswitchto a
valueof001,andselectonlytheHighmultisample.
Note: Each multisample has an up
per limit, and may not
producesoundwhenplayedabovethatlimit.
[H/L] Reverse
Themultisamplewill beplayedinreverse.Inthecase
ofFlash‐ROMmultisamplesthatwereoriginallyspeci‐
fied to loop, the multisample will be play
ed back in
“one‐shot”reversemode.Ifthemultisamplewasorigi‐
nallysettoreverse,itwillplaybackwithoutchan
ge.
Yes Themultisamplewillplaybackinreve
rse.
No Themultisamplewillplaybacknormally.
To Next Page
Loading...
Need help?
General
