185
015: Analog Rec
(Stereo Analog Record)
Thiseffectsimulatesthenoisecausedbyscratchesand
dustonanalogrecords.Italsoreproducessomeofthe
mod
ulationcausedbyawarpedturntable.
b: Flutter
This parameter enables you to set the depth of the modula-
tion caused by a warped turntable.
e: Click Level
This parameter enables you to set the level of the click noise
that occurs once every rotation
of the turntable. This simula-
tion reproduces record noise, and the noise generated after
the m
usic on a vinyl record finishes.
Pitch/phase modulation effects
016: Chorus
(Stereo Chorus)
Thiseffectaddsthicknessandwarmthtothesoundby
modulatingthede
laytimeoftheinputsignal.Youcan
addspreadtothe soundbyoffsettingthephaseofthe
leftandrightLFOsfromeachother.
e: L Pre Delay [msec], f: R Pre Delay [msec]
Setting the left and right delay time individually allows you to
control the stereo image.
a
Speed [RPM]
Sets the r.p.m. of a record
33 1/3, 45, 78
b
Flutter
Sets the modulation depth
0...100
c
Noise Density
Sets the noise density
0...100
Noise Tone
Sets the noise tone
0...100
d
Noise Level
Sets the noise level
0...100
Src
Selects the modulation source for the noise level
Off...Tempo
Amt
Sets the modulation amount of the noise level
–100...+100
e
Click Level
Sets the click noise level
0...100
,
Src Off...Tempo
Selects the modulation source for the click noise level
Amt –100...+100
Sets the modulation amount of the click noise level
f
EQ Trim
Ta bl e , “Sets the EQ input level,” on page 176
0...100
g
Pre EQ Cutoff [Hz]
Sets the EQ center frequency
300...10.00kHz
Q
Sets the EQ band width
0.5...10.0
Gain [dB]
Sets the EQ gain
–18.0...+18.0dB
h
Wet/Dry Dry, 1:99...99:1, Wet
Ta bl e , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Ta bl e , “Selects the modulation source of the effect balance,” on page 175
Amt
Ta bl e , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Analog Record
Simulation
Pre EQ
Pre EQ
EQ Trim
EQ Trim
PITCH/PHASE MOD.
a
LFO Waveform
Selects LFO Waveform
Triangle, Sine
b
LFO Phase [degree] –180...+180
Sets the LFO phase difference between the left and right Fx:010
c
LFO Frequency [Hz] 0.02...20.00Hz
Sets the LFO speed Fx:009,
Src
Selects the modulation source of LFO speed
Off...Tempo
Amt –20.00...+20.00Hz
Sets the modulation amount of LFO speed
d
BPM/MIDI Sync Off, On
Switches between using the frequency of the LFO speed and using the
tempo and notes Fx:009,
BPM
Selects MI
DI Clock and assigns tempo
MIDI, 40...240
Fx:009
Base Note
Selects the type of notes that specify the LFO speed Fx:009
Times x1...x16
Sets the number of notes that specify the LFO speed Fx:009
e
L Pre Delay [msec]
Sets the delay time for the left channel
0.0...50.0msec
f
R Pre Delay [msec]
Sets the delay time for the right channel
0.0...50.0msec
g
Depth
Sets the depth of LFO modulation
0...100
Src Off...Tempo
Selects the modulation source of the LFO modulation depth
Amt –100...+100
Sets the modulation amount of the LFO modulation depth
h
EQ Trim
Table , “Sets the EQ input level,” on page 176
0...100
i
Pre LEQ Gain [dB]
Table , “Sets the gain of Low EQ,” on page 176
–15.0...+15.0dB
Pre HEQ Gain [dB]
Table , “Sets the gain of High EQ,” on page 176
–15.0...+15.0dB
j
Wet/Dry –Wet...–1:99, Dry, 1:99...Wet
Table , “Sets the balance between the effect and dry sounds,” on page 175
Fx:010,
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 175
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
Chorus
Chorus
Left
Right
LFO Phase
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
EQ Trim
EQ Trim
LEQ
HEQ
LEQ
HEQ
LFO: Tri / Sine
To Next Page
Loading...
Need help?
General
