203
c: Envelope Select, c: Src, d: Threshold
These parameters select the source to control the start and
end of recording.
When “Envelope Select” is set to D-mod, the input signal will
be recorde
d only when the value of the modulation source
selected by the Src parameter is 64 or higher.
When “Envelope Select” is set to Input, the input signal will
be recorded
only when its level exceeds the Threshold level.
When recording is completed, reverse playback starts imme-
diately.
043: L/C/R Delay
This multitap delay outputs three Tap signals to the
left, right, andcenter respectively. You can also adjust
theleftandrightspreadofthedelaysound.
e: High Damp [%], e: Low Damp [%]
These parameters set the damping amount of high range and
low range. The tone of the delayed sound becomes darker
and lighter as it feeds back.
g: Spread
This parameter sets the pan width of the effect sound. The
ste
reo image is wi
dest with a value of 50, and the effect
sound of both channels is output from the center with a value
of 0.
044: Cross Delay
(Stereo/Cross Delay)
Thisisastereodelay,andcanbyusedasacross‐feed‐
backdela
yeffectinwhichthedelaysounds
crossover
between the left and right by changing the feedback
routing.
a
L Delay Time [msec]
Sets the delay time of TapL
0...1360msec
Level
Sets the output level of TapL
0...50
b
C Delay Time [msec]
Sets the delay time of TapC
0...1360msec
Level
Sets the output level of TapC
0...50
c
R Delay Time [msec]
Sets the delay time of TapR
0...1360msec
Level
Sets the output level of TapR
0...50
d
Feedback (C Delay)
Sets the feedback amountof TapC
–100...+100
Src Off...Tempo
Selects the modulation source of the TapC feedback amount
Amt –100...+100
Sets the modulation amount of the TapC feedback amount
e
High Damp [%]
Sets the damping amount in the high range
0...100%
Low Damp [%]
Sets the damping amount in the low range
0...100%
f
Input Level Dmod [%] –100...+100
Sets the modulation amount of the input level Fx:037,
Src
Selects the modulation source for the input level
Off...Tempo
Fx:037
g
Spread 0...50
Sets the width of the stereo image of the effect sound
h
Wet/Dry Dry, 1:99...99:1, Wet
Ta bl e , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Ta bl e , “Selects the modulation source of the effect balance,” on page 175
Amt
Ta bl e , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
C Delay
R Delay
Left
Right
Feedback
Spread
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Input Level D-mod
High Damp
Low Damp
L Delay
Input Level D-mod
+
Level
Level
Level
a
Stereo/Cross Stereo, Cross
Switches between stereo delay and cross-feedback delay
b
L Delay Time [msec]
Sets the delay time for the left channel
0.0...680.0msec
c
R Delay Time [msec]
Sets the delay time for the right channel
0.0...680.0msec
d
L Feedback
Sets the feedback amount for the left channel
–100...+100
Src Off...Tempo
Selects the modulation source of feedback amount
Amt L –100...+100
Sets the modulation amount of the left channel feedback
e
R Feedback
Sets the feedback amount for the right channel
–100...+100
Amt R –100...+100
Sets the modulation amount of the right channel feedback
f
High Damp [%]
Sets the damping amount in the high range
0...100%
Fx:043
g
Low Damp [%]
Sets the damping amount in the low range
0...100%
Fx:043
h
Input Level Dmod [%] –100...+100
Sets the modulation amount of the input level Fx:037,
Src
Selects the modulation source for the input level
Off...Tempo
Fx:037
i
Spread –50...+50
Sets the width of the stereo image of the effect sound Fx:043
j
Wet/Dry Dry, 1:99...99:1, Wet
Ta bl e , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Ta bl e , “Selects the modulation source of the effect balance,” on page 175
Amt
Ta bl e , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
Delay
Delay
Stereo/Cross
Left
Right
Feedback
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Input Level D-mod
Input Level D-mod
High Damp Low Damp
High Damp
Low Damp
Spread
Stereo/Cross