Korg microARRANGER

213
Effects
Mono – Mono Chain
066: Cmp-Par.4Eq 
(Compressor – Parametric 4-Band EQ)
This effect combines a mono‐type compressor and a
four‐band parame
tric equalizer. You can change the
orderoftheeffectconnection.
067: Cmp-ChorFlg 
(Compressor – Chorus/Flanger)
This effect combines a mono‐type compressor and a

chorus/flanger. You can change the order of the effect
connection.
h: Output Mode, i: Routing
When Wet Invert is selected, the right channel ph
ase of the
chorus/flanger effect sound is inverted. This creates pseudo-
stereo effects and adds spread.
However, if a mono-input type effect is connected after this
effect, the left
and right sounds may cancel each other, elimi-
nating the chorus/flanger effects.
When “Routing” is set to FLNGCMP, “Output Mode” will b
e
set to Normal.
a
[C] Sensitivity
Sets the sensitivity
1...100
Fx:002
b
[C] Attack
Ta bl e , “Sets the attack level,” on page 176
1...100
Fx:002
Output Level
Sets the compressor output level
0...100
Fx:002
c
[E] Trim
Sets the parametric EQ input level
0...100
d
[E] Band1 Cutoff [Hz]
Sets the center frequency of Band 1
20...1.00kHz
Q
Sets the bandwidth of Band 1
0.5...10.0
Fx:006
Gain [dB]
Sets the gain of Band 1
–18...+18dB
e
[E] Band2 Cutoff [Hz]
Sets the center frequency of Band 2
50...5.00kHz
Q
Sets the bandwidth of Band 2
0.5...10.0
Fx:006
Gain [dB]
Sets the gain of Band 2
–18...+18dB
f
[E] Band3 Cutoff [Hz]
Sets the center frequency for Band 3
300...10.00kHz
Q
Sets the bandwidth of Band 3
0.5...10.0
Fx:006
Gain [dB]
Sets the gain of Band 3
–18...+18dB
g
[E] Band4 Cutoff [Hz]
Sets the center frequency for Band 4
500...20.00kHz
Q
Sets the bandwidth of Band 4
0.5...10.0
Fx:006
Gain [dB]
Sets the gain of Band 4
–18...+18dB
h
Routing CMP  PEQ, P
EQ  CMP
Switches the order of the compressor and parametric EQ conn
ection
i
Wet/Dry Dry, 1:99...99:1, Wet
Ta bl e , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Ta bl e , “Selects the modulation source of the effect balance,” on page 175
Amt
Ta bl e , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Compressor
Trim
Parametric 4Band EQ
Output Level
Envelope - Control
Comp
a
[C] Sensitivity
Sets the sensitivity
1...100
Fx:002
b
[C] Attack
Table , “Sets the attack level,” on page 176
1...100
Fx:002
Output Level
Sets the compressor output level
0...100
Fx:002
c
[C] EQ Trim
Table , “Sets the EQ input level,” on page 176
0...100
d
[C] Pre LEQ Gain [dB]
Table , “Sets the gain of Low EQ,” on page 176
–15...+15dB
Pre HEQ Gain [dB]
Table , “Sets the gain of High EQ,” on page 176
–15...+15dB
e
[F] Delay Time [msec]
Sets the delay time
0.0...50.0msec
f
[F] LFO Frequency [Hz]
Sets the LFO speed
0.02...20.00Hz
LFO Waveform
Selects LFO Waveform
Triangle, Sine
g
[F] Depth
Sets the depth of LFO modulation
0...100
Feedback
Sets the feedback amount
–100...+100
Fx:020
h
[F] Cho/Flng Wet/Dry –Wet...–2:98, Dry, 2:98...Wet
Sets the effect balance of the chorus/flanger Fx:010, 020
Output Mode Normal, Wet Invert
Selects the output mode for the chorus/flanger 
i
Routing CMP  FLNG, FLNG  CMP
Switches the order of the compressor and chorus/fla
nger connection 
j
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 175
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Routing
Compressor
Chorus/Flanger
Chorus/Flanger
Feedback
LFO: Tri / Sine
Cho/Flng Wet / Dry
Normal
Wet Invert
Output Mode
–
+
LEQ HEQ
EQ Trim
Comp
Output Level
Envelope - Control