Korg microARRANGER

216
Effects
Mono – Mono Chain
072: Lim-Phaser
Thiseffectcombinesamono‐typelimiterand aphaser.
Youcanchangethe orderoftheeffectconnection.
073: Lim-MTapDly 
(Limiter – Multitap Delay)
Thiseffectcombines a mono‐typelimit
erand amulti‐
tap delay. You can changethe order of the effect con‐
nection.
a
[L] Ratio 1.0:1...50.0:1, Inf:1
Sets the signal compression ratio Fx:003
Threshold [dB] –40...0dB
Sets the level above which the compressor is applied Fx:003
b
[L] Attack
Sets the attack time
1...100
Fx:003
Release
Sets the release time
1...100
Fx:003
c
[L] Gain Adjust [dB]
Sets the limiter output gain
–Inf, –38...+24dB
Fx:003
d
[P] LFO Frequency [Hz]
Sets the LFO speed
0.02...20.00Hz
LFO Waveform
Selects LFO Waveform
Triangle, Sine
e
[P] Manual
Sets the frequency to which the effect is applied
0...100
f
[P] Depth
Sets the depth of LFO modulation
0...100
Resonance
Sets the resonance amount
–100...+100
Fx:023
g
[P] Phaser Wet/Dry –Wet...–2:98, Dry, 2:98...Wet
Sets the phaser effect balance Fx:010, 023
Output Mode Normal, Wet Invert
Selects the phaser output mode Fx:067
h
Routing LMTPHS, PHSLMT
Switches the order of the limiter and phaser connection Fx:067
i
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 175
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Routing
Limiter
Limiter
Gain Adjust
Envelope - Control
Phaser
Phaser
Resonance
LFO: Tri / Sine
Phaser Wet / Dry
Normal
Wet Invert
Output Mode
–
+
a
[L] Ratio 1.0:1...50.0:1, Inf:1
Sets the signal compression ratio Fx:003
Threshold [dB] –40...0dB
Sets the level above which the compressor is applied Fx:003
b
[L] Attack
Sets the attack time
1...100
Fx:003
Release
Sets the release time
1...100
Fx:003
c
[L] Gain Adjust [dB]
Sets the limiter output gain
–Inf, –38...+24dB
Fx:003
d
[D] Tap1 Time [msec]
Sets the Tap1 delay time
0...680msec
Tap1 Level
Sets the Tap1 output level
0...100
Fx:045
e
[D] Tap2 Time [msec]
Sets the Tap2 delay time
0...680msec
Feedback (Tap2)
Sets the Tap2 feedback amount
–100...+100
f
[D] Mt.Delay Wet/Dry Dry, 1:99...99:1, Wet
Sets the multitap delay effect balance
High Damp [%]
Sets the damping amount in the high range
0...100%
Fx:043
g
Routing LMTDLY, DLYLMT
Switches the order of the limiter and multitap dela
y connection
h
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 175
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Multitap Delay
Feedback
High Damp
Delay
(2)
(1)
Mt.Dly Wet / Dry
Limiter
Limiter
Gain Adjust
Envelope - Control