MacDon M155 2022 - Page 13

215676 xi Revision A
4.4.1 Engaging and Disengaging Header Safety Props............................................................................... 192
4.4.2 Header Float ............................................................................................................................. 194
Float Operating Guidelines ......................................................................................................... 194
Checking Float.......................................................................................................................... 195
Float Options ........................................................................................................................... 196
4.4.3 Leveling Header......................................................................................................................... 198
4.4.4 Header Drive Controls................................................................................................................. 201
Engaging and Disengaging Header ............................................................................................... 201
Reversing Header ..................................................................................................................... 202
4.4.5 Adjusting Header Angle............................................................................................................... 202
Checking Self-Locking Center-Link Hook ........................................................................................ 204
4.4.6 Controlling Cutting Height ........................................................................................................... 205
4.4.7 Return to Cut ............................................................................................................................ 206
Configuring Return to Cut Feature ............................................................................................... 206
Using Return to Cut Feature ....................................................................................................... 207
4.4.8 Auto Raise Height ...................................................................................................................... 208
Configuring Auto Raise Height Feature ......................................................................................... 208
Using Auto Raise Height Feature ................................................................................................. 209
4.4.9 Header Drop Rate ...................................................................................................................... 209
4.4.10 Swath Compressor ................................................................................................................... 210
Using Swath Compressor ........................................................................................................... 210
4.4.11 Double Windrow Attachment ..................................................................................................... 212
Engaging and Disengaging Double Windrow Attachment ................................................................. 213
Adjusting Double Windrow Attachment Draper Speed .................................................................... 214
4.5 Attaching and Detaching Headers.......................................................................................................... 215
4.5.1 Attaching Header Boots .............................................................................................................. 215
4.5.2 Attaching D or D1 Series Draper Header......................................................................................... 216
Attaching D or D1 Series Draper Header – Hydraulic Center-Link with Self-Alignment ........................... 216
Attaching D or D1 Series Draper Header – Hydraulic Center-Link without Self-Alignment....................... 221
Attaching D or D1 Series Draper Header – Mechanical Center-Link .................................................... 227
4.5.3 Detaching D or D1 Series Draper Header ........................................................................................ 231
Detaching D or D1 Series Draper Header – Hydraulic Center-Link ...................................................... 231
Detaching D or D1 Series Draper Header – Mechanical Center-Link ................................................... 235
4.5.4 Attaching A Series Auger Header .................................................................................................. 239
Attaching A Series Auger Header – Hydraulic Center-Link with Self-Alignment ..................................... 239
Attaching A Series Auger Header – Hydraulic Center-Link without Self-Alignment ................................ 244
Attaching A Series Auger Header – Mechanical Center-Link .............................................................. 250
4.5.5 Detaching A Series Auger Header.................................................................................................. 255
Detaching A Series Auger Header – Hydraulic Center-Link................................................................ 255
Detaching A Series Auger Header – Mechanical Center-Link ............................................................. 259
4.5.6 Attaching R Series or R1 Series Rotary Disc Header .......................................................................... 263
Attaching R or R1 Series Rotary Disc Header – Hydraulic Center-Link with Self-Alignment...................... 263
Attaching R or R1 Series Rotary Disc Header – Hydraulic Center-Link without Self-Alignment ................. 269
Attaching R or R1 Series Rotary Disc Header – Mechanical Center-Link............................................... 275
4.5.7 Detaching R or R1 Series Rotary Disc Header .................................................................................. 280
Detaching R or R1 Series Rotary Disc Header — Hydraulic Center-Link ............................................... 280
Detaching R or R1 Series Rotary Disc Header – Mechanical Center-Link .............................................. 284
4.6 Operating with D or D1 Series Draper Header.......................................................................................... 288
4.6.1 Configuring Hydraulics ................................................................................................................ 288
TABLE OF CONTENTS