5.6.5 Uni-D/ Bi-D Adjustment Menu 302
5.6 Adjustment Menu VJ628XE-M-00
(5) Setup menu
Select the Setup menu for parameter, and then press [Enter] to renew the parameter.
The default value is set to values that are suited for Mutoh ink.
Enter setting values from panel.
(5-a)Uni-D Setup
The default values for Uni-D adjustment is set to all "0" regardless of
carriage speed and head height.
Inputting Uni-D adjustment value (when Uni-D 320 VSD1 is selected)
(5-b)Bi-D Setup
The default values for Bi-D adjustment is as follows:
Inputting Bi-D adjustment value (when Bi-D 320 VSD4 is selected)
>@
>!@
[Enter]
[Enter]
㹓㹬㹧㹂㸱㸰㸮ࠉ㹔㸯ࠉ㸡㸯ࠉ㹀㸸ࠉࠉࠉ㸮
㹓㹬㹧㹂㸱㸰㸮ࠉ㹔㸯ࠉ㸡㸯ࠉ㹆㸸ࠉࠉࠉ㸮
㹓㹬㹧㹂㸱㸰㸮ࠉ㹔㸯ࠉ㸡㸯ࠉ㹅㸸ࠉࠉࠉ㸮
㹓㹬㹧㹂㸱㸰㸮ࠉ㹔㸯ࠉ㸡㸯ࠉ㹄㸸ࠉࠉࠉ㸮
㹓㹬㹧㹂㸱㸰㸮ࠉ㹔㸯ࠉ㸡㸯ࠉ㹃㸸ࠉࠉࠉ㸮
㹓㹬㹧㹂㸱㸰㸮ࠉ㹔㸯ࠉ㸡㸯ࠉ㹂㸸ࠉࠉࠉ㸮
㹓㹬㹧㹂㸱㸰㸮ࠉ㹔㸯ࠉ㸡㸯ࠉ㸿㸸ࠉࠉࠉ㸮
㹓㹬㹧㹂ࠉ㹃㹌㹂
Press [+] or [-] key to change
the setting values.
adjustment unit㸸
1 / 720 inch=approx. 35ȣm
adjustment range㸸-100㹼100
C is not printed, beacause
the position is reffered as the basis
when adjusting.
#1㸸Head Gap Low
#2㸸Head Gap High
㹓㹬㹧࣮㹂ࠉ㸱㸰㸮ࠉ㹔㹑㹂㸯㸸㹑㹣㹲㹳㹮
㹊㹭㹵ࠉ㸯㸸㹓㹬㹧࣮㹂ࠉ㸱㸰㸮ࠉ㹔㹑㹂㸯
[Enter]
[Enter]
Item default
values
Item default
values
BiD Low 320 VSD1 -40 BiD High 320 VSD1 -78
320 VSD3 -42 320 VSD3 -92
320 VSD4 -36 320 VSD4 -81
400 VSD1 -53 400 VSD1 -100
400 VSD3 -54 400 VSD3 -114
400 VSD4 -47 400 VSD4 -100
>@
>!@
[Enter]
㹀㹧㹂ࠉ㸱㸰㸮ࠉ㹔㹑㹂㸲ࠉ㸡㸯㸸ࠉࠉࠉ㸮
㹀㹧㹂ࠉ㹃㹌㹂
㹀㹧࣮㹂ࠉ㸱㸰㸮ࠉ㹔㹑㹂㸲㸸㹑㹣㹲㹳㹮
㹊㹭㹵ࠉ㸷㸸㹀㹧࣮㹂ࠉ㸱㸰㸮ࠉ㹔㹑㹂㸲
[Enter]
[Enter]
Press [+] or [-] key to change
the setting values.
adjustment unit㸸1 / 2880 inch
adjustment range㸸-400㹼400
#1㸸Head Gap Low
#2㸸Head Gap Low
To Next Page