Oce PlotWave 900 - Page 107

Oce PlotWave 900

396 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Note:

When you scan multipage 'TIFF/PDF', the scanned files will not appear on the controller

before you close the scan job on the scanner.

Chapter 3 - Define your workflow with Océ Express WebTools 107

Enable scan-to-file view

Table of Contents

Default Chapter4
- Table of Contents4
Chapter 1 Introduction11
- Notes for the Reader12
- Online Support for Your Product14
- The Océ Plotwave 90016
- The Océ Plotwave 900 Key Concepts17
- User Interaction20
- Turn the Océ Plotwave 900 on and off21
- Timers24
- Working Area27
Chapter 2 Get to Know the Océ Plotwave 900 System29
- The Océ Plotwave 900 System30
- Printer Operator Panel32
- Printer Operator Panel Actions34
- Printer Operator Panel Display35
- Select a Language36
- Media Types, Material and Sizes on the Printer37
- Stop a Print Job39
- Operator Attention Light40
- Online/Offline" Button42
Chapter 3 Define Your Workflow with Océ Express Webtools45
- Introduction46
- Load the Settings from a File67
- Restore the Factory Defaults68
- The System Monitor69
- Shut down or Restart the Controller71
- Security72
- Configure Your Printing System84
  - Change the Regional Settings84
  - Configure the Sleep Mode Timer85
- Configure and Manage Scan Destinations86
- Define Your Printing System Preferences93
- Manage Jobs on Your Printing System119
Chapter 4 Use the Océ Plotwave 900 to Print129
- The Job States130
- Send Print Jobs132
Chapter 5 Use the Océ Plotwave 900 Scanner to Copy143
- Scanner Operator Panel144
- Preference Section147
- Custom Card Start Screen148
- Templates Start Screen149
- Sections on the Display of the Scanner Operator Panel150
- Job Templates153
- Change the Operator Panel Language154
- Settings on the Océ Plotwave 900 Scanner Operator Panel155
- Perform Basic Copy Jobs157
- Make Copies158
- Select the Required Media160
- Select the Input Mode161
- Specify the Zoom Factor162
- Define Settings for the Next Original163
- Account Information164
- Use the Manual Feed for Copy Jobs165
- Stop a Job166
- Interrupt a Job167
- Stamping168
Chapter 6 Use the Océ TDS600 Scanner to Copy169
- Scanner Operator Panel170
- Section, Function and Arrow Keys172
- Preference Section173
- Custom Card Start Screen174
- Templates Start Screen175
- Job Templates176
- Sections on the Operator Panel177
- Perform Basic Copy Jobs180
- Make Copies181
- Select the Required Media182
- Select the Input Mode184
- Select the Zoom Factor185
- Select the Exposure186
- Background Compensation187
- Define Settings for the Next Original188
- Deliver Originals after Scan Jobs189
- Use the Manual Feed for Copy Jobs190
- Account Logic192
- Define the Delivery of Folded Copies193
- Interrupt a Job194
- Stop a Job195
- Stamping196
Chapter 7 Use Océ Mobile Printing and Scanning197
- Océ Mobile Webtools198
- Configure the Océ Express Webtools Settings for a Mobile Connection200
- Generate the 'Quick Response Card202
- Connect Your Mobile Device to Océ Mobile Webtools205
- Print from Your Mobile Device207
- Save a Scanned Document on Your Mobile Device209
Chapter 8 Special Copy and Scan Jobs211
- Océ Plotwave 900 Scanner212
- Océ TDS600 Scanner226
Chapter 9 The Folder, Reinforcement Unit and Belt Unit241
- Introduction242
- Folder243
- Folding Settings from the Scanner Operator Panel245
- Maximum Folding Length247
- Reinforcement Unit249
- The Belt Unit251
- Belt Full Detection254
Chapter 10 Océ Double Decker Pro255
- About the Océ Double Decker (Pro)256
- The Components257
- Product Specifications259
- How to Set the Tray Selection Method260
- How to Set the Media Separation Method261
Chapter 11 System Maintenance263
- Replace/Load a Roll of Media264
- Clear the Chip Tray270
- Add Toner271
- Clean the Océ Plotwave 900 Scanner273
- Clean the Océ TDS600 Scanner275
- Introduction to Reinforcement Unit Maintenance277
- Insert a New Tape Roll278
- Empty the Waste Box286
- Clean the Reinforcement Knives288
- Empty the Waste Basket of the Punch Unit290
Chapter 12 Solve Problems291
- Introduction292
- Job Error Reports293
- Troubleshooting299
Chapter 13 Support329
- Service Required Indication330
- Online Services331
- Update the System Software333
Chapter 14 License Management335
- Introduction to Managing Licenses336
- The 'Licenses' Tab in the Océ Express Webtools337
- The Basic Workflow of 'Support' - 'Licenses' Activation338
- Océ License Logic339
- The Structure of License Files and Licenses340
- Check Your Licenses342
- Save the Currently Active Licenses344
- Install a New License345
Chapter 15 Account Management347
- An Overview of Océ Account Center348
- Océ Account Console350
Chapter 16 Software Options357
- Océ Repro Desk Studio358
- Network and Security Settings359
Chapter 17 Network and Security Settings359
- Check or Adapt the Network Settings360
- System Specifications361
Appendix A System Specifications361
- Specifications Océ Plotwave 900 Printer362
- Specifications Océ Plotwave 900 Scanner364
- Specifications Océ TDS600 Scanner366
- Specifications Océ Plotwave 900 Controller368
- Specifications Folder and Reinforcement Unit (Optional)370
- Specifications Océ Delivery Tray (Optional)371
- Specifications Océ Double Decker Pro (Optional)372
- Specifications Delivery Belt Unit (Optional)373
- Preferred Océ Media Types and Sizes374
- Standard Scale Factor377
Appendix B Reader's Comment Sheet379
- Online Support for Your Product380
- Reader's Comment Sheet382

Other manuals for Oce PlotWave 900

Specifications2 pages

Related product manuals

Preview: Oce PlotWave 300

Oce PlotWave 300

Preview: Oce PlotWave 350

Oce PlotWave 350

Preview: Oce PlotWave 340

Oce PlotWave 340

Preview: Oce plotwave 345

Oce plotwave 345

Preview: Oce PlotWave 750

Oce PlotWave 750

Oce PlotWave 360

Oce plotwave 365

Preview: Oce 9300

Preview: Oce ColorWave 600

Oce ColorWave 600

Preview: Oce ColorWave 650

Oce ColorWave 650

Preview: Oce VarioPrint i Series

Oce VarioPrint i Series