To Next Page

To Previous Page

Stop a job

Introduction

Press the Stop key to interrupt the original transport on the scanner.

How to stop a job

Press the Stop key. The original transport is now stopped and you are prompted to open

the scanner cover and remove the original.

Open the cover, remove the original and close the cover again. You are now ready to start

the next copy job.

Chapter 6 - Use the Océ TDS600 scanner to copy 195

Stop a job

Default Chapter4
- Table of Contents4
Chapter 1 Introduction11
- Notes for the Reader12
- Online Support for Your Product14
- The Océ Plotwave 90016
- The Océ Plotwave 900 Key Concepts17
- User Interaction20
- Turn the Océ Plotwave 900 on and off21
- Timers24
- Working Area27
Chapter 2 Get to Know the Océ Plotwave 900 System29
- The Océ Plotwave 900 System30
- Printer Operator Panel32
- Printer Operator Panel Actions34
- Printer Operator Panel Display35
- Select a Language36
- Media Types, Material and Sizes on the Printer37
- Stop a Print Job39
- Operator Attention Light40
- Online/Offline" Button42
Chapter 3 Define Your Workflow with Océ Express Webtools45
- Introduction46
- Load the Settings from a File67
- Restore the Factory Defaults68
- The System Monitor69
- Shut down or Restart the Controller71
- Security72
- Configure Your Printing System84
  - Change the Regional Settings84
  - Configure the Sleep Mode Timer85
- Configure and Manage Scan Destinations86
- Define Your Printing System Preferences93
- Manage Jobs on Your Printing System119
Chapter 4 Use the Océ Plotwave 900 to Print129
- The Job States130
- Send Print Jobs132
Chapter 5 Use the Océ Plotwave 900 Scanner to Copy143
- Scanner Operator Panel144
- Preference Section147
- Custom Card Start Screen148
- Templates Start Screen149
- Sections on the Display of the Scanner Operator Panel150
- Job Templates153
- Change the Operator Panel Language154
- Settings on the Océ Plotwave 900 Scanner Operator Panel155
- Perform Basic Copy Jobs157
- Make Copies158
- Select the Required Media160
- Select the Input Mode161
- Specify the Zoom Factor162
- Define Settings for the Next Original163
- Account Information164
- Use the Manual Feed for Copy Jobs165
- Stop a Job166
- Interrupt a Job167
- Stamping168
Chapter 6 Use the Océ TDS600 Scanner to Copy169
- Scanner Operator Panel170
- Section, Function and Arrow Keys172
- Preference Section173
- Custom Card Start Screen174
- Templates Start Screen175
- Job Templates176
- Sections on the Operator Panel177
- Perform Basic Copy Jobs180
- Make Copies181
- Select the Required Media182
- Select the Input Mode184
- Select the Zoom Factor185
- Select the Exposure186
- Background Compensation187
- Define Settings for the Next Original188
- Deliver Originals after Scan Jobs189
- Use the Manual Feed for Copy Jobs190
- Account Logic192
- Define the Delivery of Folded Copies193
- Interrupt a Job194
- Stop a Job195
- Stamping196
Chapter 7 Use Océ Mobile Printing and Scanning197
- Océ Mobile Webtools198
- Configure the Océ Express Webtools Settings for a Mobile Connection200
- Generate the 'Quick Response Card202
- Connect Your Mobile Device to Océ Mobile Webtools205
- Print from Your Mobile Device207
- Save a Scanned Document on Your Mobile Device209
Chapter 8 Special Copy and Scan Jobs211
- Océ Plotwave 900 Scanner212
- Océ TDS600 Scanner226
Chapter 9 The Folder, Reinforcement Unit and Belt Unit241
- Introduction242
- Folder243
- Folding Settings from the Scanner Operator Panel245
- Maximum Folding Length247
- Reinforcement Unit249
- The Belt Unit251
- Belt Full Detection254
Chapter 10 Océ Double Decker Pro255
- About the Océ Double Decker (Pro)256
- The Components257
- Product Specifications259
- How to Set the Tray Selection Method260
- How to Set the Media Separation Method261
Chapter 11 System Maintenance263
- Replace/Load a Roll of Media264
- Clear the Chip Tray270
- Add Toner271
- Clean the Océ Plotwave 900 Scanner273
- Clean the Océ TDS600 Scanner275
- Introduction to Reinforcement Unit Maintenance277
- Insert a New Tape Roll278
- Empty the Waste Box286
- Clean the Reinforcement Knives288
- Empty the Waste Basket of the Punch Unit290
Chapter 12 Solve Problems291
- Introduction292
- Job Error Reports293
- Troubleshooting299
Chapter 13 Support329
- Service Required Indication330
- Online Services331
- Update the System Software333
Chapter 14 License Management335
- Introduction to Managing Licenses336
- The 'Licenses' Tab in the Océ Express Webtools337
- The Basic Workflow of 'Support' - 'Licenses' Activation338
- Océ License Logic339
- The Structure of License Files and Licenses340
- Check Your Licenses342
- Save the Currently Active Licenses344
- Install a New License345
Chapter 15 Account Management347
- An Overview of Océ Account Center348
- Océ Account Console350
Chapter 16 Software Options357
- Océ Repro Desk Studio358
- Network and Security Settings359
Chapter 17 Network and Security Settings359
- Check or Adapt the Network Settings360
- System Specifications361
Appendix A System Specifications361
- Specifications Océ Plotwave 900 Printer362
- Specifications Océ Plotwave 900 Scanner364
- Specifications Océ TDS600 Scanner366
- Specifications Océ Plotwave 900 Controller368
- Specifications Folder and Reinforcement Unit (Optional)370
- Specifications Océ Delivery Tray (Optional)371
- Specifications Océ Double Decker Pro (Optional)372
- Specifications Delivery Belt Unit (Optional)373
- Preferred Océ Media Types and Sizes374
- Standard Scale Factor377
Appendix B Reader's Comment Sheet379
- Online Support for Your Product380
- Reader's Comment Sheet382

Other manuals for Oce PlotWave 900

Specifications2 pages

Questions and Answers:

Need help?

Do you have a question about the Oce PlotWave 900 and is the answer not in the manual?

Océ PlotWave 900

Media Handling

tray capacity	2 x 750 sheets - 20lb Bond
media width	8.5” x 36”
media length	8.5” x 48”
media weight	16 - 29 lb Bond

Sound Levels

sound level standby	≤ 35 dB (A)
sound level active	≤ 71 dB (A)

Electrical

voltage	100 – 240 V
frequency	50 – 60 Hz

Weight and Dimensions

required floor space	59.1” (W) x 63.0” (D) x 43.3” (H)
weight	309 lbs.

Océ TDS750

Electrical

voltage	100 – 240 V
frequency	50 – 60 Hz

View in Manual

Related product manuals

Oce PlotWave 900 User Manual

Table of Contents