Orion A10E - Figure 5-5 Applying IGMP Filtering in the VLAN

To Next Page

To Previous Page

Orion Networks

A10E/A28E/A28F Configuration Guide

5 Multicast

Orion Networks

143

Figure 5-5 Applying IGMP filtering in the VLAN

Configuration steps

Step 1 Create a VLAN, and create IGMP filtering rules.

Alpha-A28E#config

Alpha-A28E(config)#creat vlan 3,12,13 active

Alpha-A28E(config)#ip igmp profile 1

Alpha-A28E(config-igmp-profile)#range 234.5.6.7 234.5.6.10

Alpha-A28E(config-igmp-profile)#permit

Step 2 Enable MVR and IGMP filtering.

Alpha-A28E(config)#mvr enable

Alpha-A28E(config)#mvr vlan 3

Alpha-A28E(config)#mvr vlan 3 group

234.5.6.7 5

Alpha-A28E(config)#ip igmp filter

Step 3 Configure the source interface.

Alpha-A28E(config)#ip igmp filter 1 vlan 12

Alpha-A28E(config)#ip igmp max-group 1 vlan 12

Alpha-A28E(config)#ip igmp max-group action replace vlan

Step 4 Configure the receiving interface on the set top box, and apply IGMP filtering rule and set the

maximum multicast group number.

Main Page

Preface3
- Versions3
- Conventions3
1 Basic Configurations21
- Accessing the Device21
  - Introduction21
  - Accessing from the Console Interface22
- Figure 1-1 Accessing the A10E/A28E through PC Connected with Console Interface22
- Accessing from Telnet23
- Figure 1-2 Communication Parameters Configuration in Hyper Terminal23
- Mouse Operation23
Contents24
- Accessing from Sshv224
- Managing Users34
  - Checking Configurations35
- Restoring Default Value of Command Line34
- Managing Files35
  - Managing Bootrom Files35
Tables38
- Managing Configuration Files38
- Checking Configurations39
- Configuring Clock Management39
- Configuring Interface Management42
- Configuring Basic Information46
- Task Scheduling47
- Watchdog47
- Load and Upgrade48
Figure 1-5 Configuring Auto-Loading52
2 Ethernet54
- MAC Address Table54
- Vlan60
  - Introduction60
  - Example for Configuring Selective Qinq71
- Configuring Basic Qinq67
- Configuring Selective Qinq67
- Default Configurations of Qinq67
- Preparing for Configurations67
- Checking Configurations68
- Configuring the Egress Interface Totrunk Mode68
- Maintenance68
- Example for Configuring Basic Qinq69
Figure 2-11 Layer 2 Protocol Transparent Transmission Application Networking89
3 IP Services92
- Arp92
- Layer 3 Interface96
- Figure 3-3 DHCP Typical Application Networking101
- Preparing for Configurations103
- Optional) Configuring DHCP Client104
- Optional) Renewing or Releasing the IP Address104
- Checking Configurations105
- Configuring DHCP Clients Application105
4 Qos116
- Introduction116
- Figure 4-1 Traffic Classification118
- Figure 4-5 Structure of Cos Priority Packets119
- Traffic Policy119
- Congestion Management120
- Priority Mapping120
Figure 4-9 Rate Limiting Based on Interface137
5 Multicast139
- Overview139
- Mvr142
- MVR Proxy142
- IGMP Filtering143
- Configuring IGMP Snooping144
- Configuring MVR148
- Configuring MVR Proxy150
- Configuring IGMP Filtering152
- Maintenance155
- Configuration Examples156
  - Example for Configuring IGMP Snooping156
Figure 5-5 Applying IGMP Filtering in the VLAN163
6 Security165
- Acl165
- Secure MAC Address172
- Dynamic ARP Inspection179
  - Introduction179
  - IP Source Guard204
    - Introduction204
- Preparing for Configruations199
- Configuring Basic Functions of 802.1X200
- Default Configurations of 802.1X200
- Configuring 802.1X Re-Authentication201
- Configuring 802.1X Timers201
- Checking Configurations202
- Maintenance202
- Example for Configuring 802.1X203
Figure 6-15 Line Detection Application Networking223
7 Reliability225
- Link Aggregation225
- Example for Configuring Static LACP Link Aggregation231
  - Figure 7-4 Application of Interface Backup in Different Vlans234
  - Failover239
- Configuring Basic Functions of Interface Backup235
- Default Configurations of Interface Backup235
- Preparing for Configurations235
- Checking Configurations236
- Optional) Configuring Force Switching on Interfaces236
- Example for Configuring Interface Backup237
Figure 7-17 RRPS Application Networking279
8 Oam282
- Efm282
- Configuring Basic Functions of EFM284
- Default Configurations of EFM284
- Configuring Active Functions of EFM285
- Configuring Passive Functions of EFM287
- Checking Configurations288
- Example for Configuring EFM289
- Preparing for Configurations292
- Default Configurations of CFM293
- Configuring Basic CFM Functions294
- Enabling CFM294
- Configuring Fault Detection295
- Configuring Fault Acknowledgement297
- Configuring Fault Location298
- Checking Configurations299
- Maintenance299
- Example for Configuring CFM300
Figure 8-6 SLA Application Networking306
9 System Management308
- Snmp308
- Default Configurations of SNMP310
- Preparing for Configurations310
- Configuring Basic Functions of SNMP V1/V2C311
- Configuring Basic Functions of SNMP V3312
- Figure 9-8 LLDPDU Structure329
- Extended OAM336
  - Introduction336
10 Appendix364
- Terms364
- Abbreviations369

Orion A10E - Figure 5-5 Applying IGMP Filtering in the VLAN

Table of Contents