Siemens MICROMASTER 440 - Motorized Potentiometer (MOP); Setpoint Memory of the MOP; Inhibit Negative MOP Setpoints; BI: Enable MOP (UP-Command)

To Next Page

To Previous Page

Parameter Description Issue 01/06

MICROMASTER 440 Parameter List

120 6SE6400-5BB00-0BP0

3.18 Motorized potentiometer (MOP)

P1031[3] Setpoint memory of the MOP Min: 0

CStat: CUT Datatype: U16 Unit: - Def: 0

P-Group: SETPOINT Active: Immediately QuickComm.: No Max: 1

Saves last motor potentiometer setpoint (MOP) that was active before OFF command or power down.

Possible Settings:

0 MOP setpoint will not be stored

1 MOP setpoint will be stored (P1040 is updated)

Index:

P1031[0] : 1st. Drive data set (DDS)

P1031[1] : 2nd. Drive data set (DDS)

P1031[2] : 3rd. Drive data set (DDS)

Note:

On next ON command, motor potentiometer setpoint will be the saved value in parameter P1040 (setpoint

of the MOP).

P1032 Inhibit negative MOP setpoints Min: 0

CStat: CT Datatype: U16 Unit: - Def: 1

P-Group: SETPOINT Active: first confirm QuickComm.: No Max: 1

This parameter suppresses negative setpoints of the MOP output r1050.

Possible Settings:

0 Neg. MOP setpoint is allowed

1 Neg. MOP setpoint inhibited

Note:

The reversing functions (e.g. BOP-Reverse button if P0700 = 1) are not affected by the settings of P1032.

Use P1110 to fully prevent change of direction in setpoint channel.

P1035[3] BI: Enable MOP (UP-command) Min: 0:0

CStat: CT Datatype: U32 Unit: - Def: 19:13

P-Group: COMMANDS Active: first confirm QuickComm.: No Max: 4000:0

Defines source for motor potentiometer setpoint increase frequency.

Index:

P1035[0] : 1st. Command data set (CDS)

P1035[1] : 2nd. Command data set (CDS)

P1035[2] : 3rd. Command data set (CDS)

Common Settings:

722.0 = Digital input 1 (requires P0701 to be set to 99, BICO)

722.1 = Digital input 2 (requires P0702 to be set to 99, BICO)

722.2 = Digital input 3 (requires P0703 to be set to 99, BICO)

722.3 = Digital input 4 (requires P0704 to be set to 99, BICO)

722.4 = Digital input 5 (requires P0705 to be set to 99, BICO)

722.5 = Digital input 6 (requires P0706 to be set to 99, BICO)

722.6 = Digital input 7 (via analog input 1, requires P0707 to be set to 99)

722.7 = Digital input 8 (via analog input 2, requires P0708 to be set to 99)

19.D = MOP up via BOP

P1036[3] BI: Enable MOP (DOWN-command) Min: 0:0

CStat: CT Datatype: U32 Unit: - Def: 19:14

P-Group: COMMANDS Active: first confirm QuickComm.: No Max: 4000:0

Defines source for motor potentiometer setpoint decrease frequency.

Index:

P1036[0] : 1st. Command data set (CDS)

P1036[1] : 2nd. Command data set (CDS)

P1036[2] : 3rd. Command data set (CDS)