General-purpose timers (TIM2/TIM3/TIM4/TIM5) RM0440
1320/2126 RM0440 Rev 4
Bits 6:4 OC1M[2:0]: Output compare 1 mode
These bits define the behavior of the output reference signal tim_oc1ref from which tim_oc1
is derived. tim_oc1ref is active high whereas tim_oc1 active level depends on CC1P bit.
0000: Frozen - The comparison between the output compare register TIMx_CCR1 and the
counter TIMx_CNT has no effect on the outputs.(this mode is used to generate a
timing base).
0001: Set channel 1 to active level on match. tim_oc1ref signal is forced high when the
counter TIMx_CNT matches the capture/compare register 1 (TIMx_CCR1).
0010: Set channel 1 to inactive level on match. tim_oc1ref signal is forced low when the
counter TIMx_CNT matches the capture/compare register 1 (TIMx_CCR1).
0011: Toggle - tim_oc1ref toggles when TIMx_CNT=TIMx_CCR1.
0100: Force inactive level - tim_oc1ref is forced low.
0101: Force active level - tim_oc1ref is forced high.
0110: PWM mode 1 - In upcounting, channel 1 is active as long as TIMx_CNT<TIMx_CCR1
else inactive. In downcounting, channel 1 is inactive (tim_oc1ref=0) as long as
TIMx_CNT>TIMx_CCR1 else active (tim_oc1ref=1).
0111: PWM mode 2 - In upcounting, channel 1 is inactive as long as
TIMx_CNT<TIMx_CCR1 else active. In downcounting, channel 1 is active as long as
TIMx_CNT>TIMx_CCR1 else inactive.
1000: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger
event is detected (on tim_trgi signal). Then, a comparison is performed as in PWM
mode 1 and the channels becomes inactive again at the next update. In down-
counting mode, the channel is inactive until a trigger event is detected (on tim_trgi
signal). Then, a comparison is performed as in PWM mode 1 and the channels
becomes inactive again at the next update.
1001: Retriggerable OPM mode 2 - In up-counting mode, the channel is inactive until a
trigger event is detected (on tim_trgi signal). Then, a comparison is performed as in
PWM mode 2 and the channels becomes inactive again at the next update. In down-
counting mode, the channel is active until a trigger event is detected (on tim_trgi
signal). Then, a comparison is performed as in PWM mode 1 and the channels
becomes active again at the next update.
1010: Reserved.
1011: Reserved.
1100: Combined PWM mode 1 - tim_oc1ref has the same behavior as in PWM mode 1.
tim_oc1refc is the logical OR between tim_oc1ref and tim_oc2ref.
1101: Combined PWM mode 2 - tim_oc1ref has the same behavior as in PWM mode 2.
tim_oc1refc is the logical AND between tim_oc1ref and tim_oc2ref.
1110: Asymmetric PWM mode 1 - tim_oc1ref has the same behavior as in PWM mode 1.
tim_oc1refc outputs tim_oc1ref when the counter is counting up, tim_oc2ref when it is
counting down.
1111: Asymmetric PWM mode 2 - tim_oc1ref has the same behavior as in PWM mode 2.
tim_oc1refc outputs tim_oc1ref when the counter is counting up, tim_oc2ref when it is
counting down.
Note: In PWM mode, the tim_ocref_clr level changes only when the result of the comparison
changes or when the output compare mode switches from “frozen” mode to “PWM”
mode.
To Next Page
Loading...
Need help?
General
