YASKAWA V1000 Series Technical Manual

Connecting a Noise Filter .......................................................................................................................... 272
EMC Filter Installation............................................................................................................................... 274
Installing a Motor Thermal Overload (OL) Relay on the Drive Output .................................................................. 276
8.5 Communication Options....................................................................................................................... 278
8.6 Connecting an Option Card .................................................................................................................. 279
Verifying Option Card and Product Type ....................................................................................................... 279
Connecting the Option Card ....................................................................................................................... 279
A. SPECIFICATIONS...................................................................................................................... 281
A.1 Heavy Duty and Normal Duty Ratings................................................................................................... 282
A.2 Single/Three-Phase 200 V Class Drive.................................................................................................. 283
A.3 Three-Phase 400 V Class Drives ........................................................................................................... 285
A.4 Drive Specifications.............................................................................................................................. 286
A.5 Drive Watts Loss Data .......................................................................................................................... 288
A.6 Drive Derating Data............................................................................................................................... 290
Carrier Frequency Derating........................................................................................................................ 290
Temperature Derating............................................................................................................................... 290
Altitude Derating ...................................................................................................................................... 290
B. PARAMETER LIST .................................................................................................................... 293
B.1 Parameter Groups ................................................................................................................................ 294
B.2 Parameter Table.................................................................................................................................... 295
A: Initialization Parameters ........................................................................................................................ 295
b: Application .......................................................................................................................................... 295
C: Tuning ............................................................................................................................................... 298
d: References ......................................................................................................................................... 300
E: Motor Parameters ................................................................................................................................ 302
F: Options .............................................................................................................................................. 304
H Parameters: Multi-Function Terminals ....................................................................................................... 306
L: Protection Function ............................................................................................................................... 310
n: Advanced Performance Set-Up ............................................................................................................... 315
o: Operator Related Parameters ................................................................................................................. 316
r: DWEZ Parameters ................................................................................................................................ 317
T: Motor Tuning ....................................................................................................................................... 318
U: Monitors ............................................................................................................................................ 318
Control Mode Dependent Parameter Default Values ....................................................................................... 322
V/f Pattern Default Values.......................................................................................................................... 323
Default Settings Determined by Drive Capacity (o2-04) and Normal / Heavy Duty Selection (C6-01) ......................... 323
Parameters that Change with the Motor Code Selection .................................................................................. 325
C. MEMOBUS/MODBUS COMMUNICATIONS ............................................................................. 329
C.1 MEMOBUS/Modbus Hardware .............................................................................................................. 330
Communication Specifications .................................................................................................................... 330
Communication Terminal Resistance ........................................................................................................... 330
Connecting a PLC.................................................................................................................................... 330
C.2 MEMOBUS/Modbus Parameters ........................................................................................................... 332
MEMOBUS/Modbus Parameters................................................................................................................. 332
C.3 Related Parameters .............................................................................................................................. 334
C.4 Message Format ................................................................................................................................... 335
Slave Address......................................................................................................................................... 335
Function Code......................................................................................................................................... 335
Data...................................................................................................................................................... 335
Error Check ............................................................................................................................................ 335
C.5 Command/Response Message Format ................................................................................................. 336
Reading Drive Memory Register Contents..................................................................................................... 336
Loop Back Test ....................................................................................................................................... 336
Writing to Multiple Registers....................................................................................................................... 336
C.6 MEMOBUS/Modbus Data Table............................................................................................................. 337
Command Data ....................................................................................................................................... 337
Monitor Data ........................................................................................................................................... 337
Broadcast Messages ................................................................................................................................ 339
C.7 Enter Command.................................................................................................................................... 340
ENTER Command Settings when Upgrading the Drive .................................................................................... 340
C.8 Error Codes .......................................................................................................................................... 341
Table of Contents
YASKAWA ELECTRIC SIEP C710606 18A YASKAWA AC Drive – V1000 Technical Manual (Preliminary)
7

YASKAWA V1000 Series Specifications

General

Model	V1000 Series
Series	V1000
Output Frequency	0.1 to 400 Hz
Overload Capacity	150% for 60 seconds
Type	AC Drive
Control Method	V/f Control
Input Voltage	200-240V, 380-480V
Output Voltage	0 to Input Voltage
Power Range	0.1 to 18.5 kW
Horsepower	0.2 to 25 HP
Protection Features	Overcurrent, Overvoltage, Undervoltage, Overheating, Short Circuit, Ground Fault
Communication Interfaces	Modbus RTU
Enclosure	IP20
Ambient Temperature	-10 to +50°C
Storage Temperature	-20 to +60°C
Humidity	5 to 95% RH (non-condensing)
Cooling Method	Fan Cooled