YASKAWA V1000 Series

Index
Symbols
(Terminal MP) Pulse Train Monitor Selection, 310, 358
(Terminal RP) Pulse Train Input Function Selection, 310, 358
Numerics
10th Most Recent Fault, 90, 217, 320, 360
2nd Most Recent Fault, 90, 217, 320, 360
2-Wire Initialization, 75
2-Wire Sequence, 78
3rd Most Recent Fault, 90, 217, 320, 360
3-Wire Initialization, 75
3-Wire Sequence, 78, 78, 306
3-Wire Sequence Example, 35
4th Most Recent Fault, 90, 217, 320, 360
5th Most Recent Fault, 90, 217, 320, 360
6th Most Recent Fault, 90, 217, 320, 360
7th Most Recent Fault, 90, 217, 320, 360
8th Most Recent Fault, 90, 217, 320, 360
9th Most Recent Fault, 90, 217, 320, 360
A
A/D Conversion Error, 226, 226, 226, 229, 230
A1-01, 96, 295
A1-02, 75, 93, 211, 233, 244, 249, 249, 250, 252, 295, 357
A1-03, 70, 4, 78, 96, 229, 230, 295, 357
A1-04, 97, 248, 295
A1-05, 97, 248, 295, 357
A1-06, 295
A1 Initialization Parameters, 295
A2-01, 97
A2-01 to A2-32, 295, 357
A2-32, 97
A2-33, 70, 97, 295, 357
A2 User Parameters, 295
Accel/Decel, 81, 81
Accel/Decel Ramp Hold, 306
Accel/Decel Time, 225
Accel/Decel Time 1, 306
Accel/Decel Time Selection 2, 306
Accel/Decel Time Setting Units, 298, 357
Accel/Decel Time Switching Frequency, 298, 357
Acceleration/Deceleration, 4, 81
Acceleration Error, 228, 245
Acceleration Time 1, 80, 298, 357
Acceleration Time 2, 298, 357
Acceleration Time 3 (Motor 2 Accel Time 1), 298, 357
Acceleration Time 4, 298, 298, 357, 357
Acceleration Time Pull-In Current, 316
Access Level Selection, 96, 295
Accumulated Operation Time, 90, 217, 321
Accumulated Operation Time Selection, 317, 359
Accumulated Operation Time Setting, 317, 359
Adjusting the Monitor Output, 87
AFR Gain, 224
AFR Time Constant 1, 224
AFR Time Constant 2, 224
Alarm, 228, 308
Alarms and Errors, 226
Ambient Temperature Setting, 290, 314
Analog Filter Time Constant, 225
Analog Frequency Reference Fluctuation Limit (Up/Down 2), 301, 358
Analog Input Filter Time Constant, 309, 358
Application Selection, 295
ASR Integral Time 1 (for Simple PG V/f Control), 299, 357
ASR Integral Time 2 (for Simple PG V/f Control), 299, 357
ASR Limit (for Simple PG V/f Control), 299, 357
ASR Proportional Gain 1 (for Simple PG V/f Control), 299, 357
ASR Proportional Gain 2 (for Simple PG V/f Control), 299, 357
Automatic Reduction Selection for Stall Prevention during Run, 312, 359
Auto Restart Operation Selection, 312, 359
Auto-Tuning, 4, 91, 92, 93, 93, 94, 94, 95, 95, 210, 5, 5, 211, 5, 212, 212, 6
Auto-Tuning Codes, 6
Auto-Tuning Fault Codes, 93, 5
Auto-Tuning Fault Detection, 245
Auto-Tuning Fault Solutions, 6
Auto-Tuning for V/f Control, 91, 210
Auto-Tuning Mode Selection, 94, 318
Auxiliary Frequency Reference 1, 309
B
Baseblock, 238
Baseblock 2, 308
Baseblock Command (N.C.), 306
Baseblock Command (N.O.), 306
Baseblock Signal Input, 227, 227, 240, 240
Base Frequency, 234
Basic Drive Operation, 66
Bi-Directional Speed Search Selection, 296, 357
Braking Resistor, 52
Braking Resistor, Installation, 4
Braking Resistor Adjustments, 52
Braking Resistor Fault, 308
Braking Resistor Overheat, 236
Buzzing Sound from Motor at 2 kHz, 253
C
C1-01, 64, 64, 4, 245, 245, 250, 298, 298, 298, 357, 357
C1-01, -03, -05, -07, 232
C1-01 through C1-08, 231, 233, 234, 234, 234, 236, 236, 239, 240, 240
C1-01 through C1-11, 225
C1-02, 80, 229, 251, 298, 357
C1-02, -04, -06, -08, 235
C1-02, -04, -06 and -08, 235
C1-03, 250, 298, 357
C1-04, 251, 298, 357
C1-05, 250
C1-06, 251, 357
C1-07, 250, 298, 357
C1-08, 251, 298, 357
C1-09, 81, 298, 357
C1-10, 81, 298, 357
C1-11, 81, 298, 357
C1 Acceleration and Deceleration Times, 298
C2-01, 236, 299, 357
C2-01 through C2-04, 225, 232
C2-02, 299, 357
YASKAWA ELECTRIC SIEP C710606 18A YASKAWA AC Drive – V1000 Technical Manual (Preliminary)
361