EasyManuals Logo

Korg M3 Parameter Guide

Korg M3
647 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #150 background imageLoading...
Page #150 background image
Combination mode
140
Off (unchecked): X–Y position will not affect the volume.
However, you can use program parameter settings for X–Y
CC or AMS to control the volume.
Equal Amount [Off, On]
This applies only when Enable Volume Control is On.
When Equal Amount is On, the X–Y will fade between all
four X–Y axes while maintaining a total amount of 100%.
This provides a smooth fade between the different sounds,
and is the type of volume control used by classic Vector
synths.
Note that this will work best when the Programs assigned to
each of the four axes have equivalent volumes. For instance,
you might create a Combination with four Programs, each
sounding at the same volume and assigned to a different
axis. You could then add a fifth Program, assign it to one of
the axes, and then use the Timbre volume sliders to reduce
the levels of both Programs on that axis by 50%–so that their
combined volume is the same as any one of the other
Programs.
Also, when this is checked, the Center Volume parameters
will be grayed out, since Equal Amount sets them
automatically.
Combi X–Y CC Control
Combi switch:
“Enable CC control”
X–Y CC MIDI Output
Global switch:
“X–Y MIDI Out”
Timbre 1
Timbre 16
Program X–Y Volume Control
Program X–Y CC Control
Combi X–Y Volume Control
Combi switch:
“Enable Volume control”
Combination
X–Y TouchView
X–Y CC Control
X–Y CC MIDI Output
Program switch:
“Enable Volume control”
Program switch:
“Enable CC control”
X–Y Modulation of
Timbre Volume
Timbres 1–16
Center Volume and
Equal Amount settings
X Mode and
Y Modes
X+/– and Y+/–
CC Assignments
X–Y CC Modulation of
Program and FX Parameters
(Global Channel Only)
Global Controllers
MIDI CC Assignments
Defaults: X=118, Y=119
X–Y Modulation of
Osc 1–2 Volume
Osc 1–2 Center Volume
and Equal Amount settings
X Mode and
Y Modes
X+/– and Y+/–
CC Assignments
X–Y CC Modulation of
Program Parameters
X–Y control
MIDI In
(Global Chan.)
X–Y control
MIDI In
(Timbre Chan.)
X–Y motion
X–Y control
In X-Y control, only timbres that are set to
the global MIDI channel will be controlled
* Depending on the MIDI I/O settings of the KARMA module,
timbres other than the global MIDI channel will also be
controlled.
X
–Y Synthesis system, Combination mode

Table of Contents

Other manuals for Korg M3

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Korg M3 and is the answer not in the manual?

Korg M3 Specifications

General IconGeneral
Synthesis TypeEDS (Enhanced Definition Synthesis)
Sound EngineEDS (Enhanced Definition Synthesis)
MIDIIn, Out, Thru
Keyboard61-key, velocity-sensitive, aftertouch
Sequencer16-track MIDI sequencer
SamplingOpen Sampling System
DisplayTouchView graphical user interface with 320x240 color TFT LCD
Arpeggiator2 polyphonic arpeggiators
ControllersJoystick, Ribbon Controller
OutputsL/MONO, R, Individual 1-4, Headphones
USBYes, USB MIDI
StorageSD card slot
Combinations1, 792 user combinations
Polyphony120 voices (max)
Effects5 Insert effects, 2 Master effects, 1 Total effect

Related product manuals