Sampling P4: Controllers 4–1: Setup
319
Sampling P4: Controllers
4–1: Setup
Here you can specify the SW1 and SW2 switch and 5–8
slider functions of the Sampling mode when Control Assign
REALTIME CONTROL is selected.
Note: SW1 and SW2 can be controlled by the KYBD-61/73/
88’s SW1 and SW2 switches.
In Sampling mode, it is not possible to use AMS to
control program parameters.
4–1a: Panel Switch Assign
SW1 (SW1 Assign) [Off, ..., After Touch Lock]
This assigns the function of SW1.For more information,
please see “List of SW 1/2 assignments” on page 597.
Mode (SW1 Mode) [Toggle, Momentary]
This specifies the on/off operation when you press the
KYBD-61/73/88’s SW1 switch.
Toggle: The state will alternate between On and Off each
time you press the SW1 switch.
Momentary: The state will remain On only while you
continue holding down the SW1 switch.
SW2 (SW2 Assign) [Off, ..., After Touch Lock]
Mode (SW2 Mode) [Toggle, Momentary]
This assigns the function of SW2. The functions that can be
assigned to SW2 are the same as for SW1, with the
substitution of SW2 Mod. (CC#81) instead of the SW1’s SW1
Mod. (CC#80).
4–1b: Realtime Control Slider Assign
Here you can assign the functions (mainly types of control
change) that sliders 5–8 will have when Control Assign
REALTIME CONTROL is selected. (See “1–6b: Realtime
Control Slider Assign” on page 35)
The functions you assign here are active when you select
CONTROL ASSIGN REALTIME CONTROL and operate
sliders 5–8.
Slider 5 [Off, ..., MIDI CC#95]
Slider 6 [Off, ..., MIDI CC#95]
Slider 7 [Off, ..., MIDI CC#95]
Slider 8 [Off, ..., MIDI CC#95]
Example settings)
In this example, we’ll use realtime modulation slider 5 to
control the “Wet/Dry” parameter of the 056: Stereo/Cross
Delay assigned to IFX1, and use slider 6 to control the post-
IFX “Pan.” Then we’ll sample an audio signal from an
external source while controlling these parameters in
realtime.
1. Set Bus Select (0–2a) to IFX1.
2. Select 056: Stereo/CrossDelay for “IFX1.”
3. Set the IFX1 page “Wet/Dry” setting to Dry, “Src
(Source)” to Slider M5[+], and “Amt” to +50.
4. In the Realime Control Slider Assign area, assign
“Slider 5” to Slider Mod.5 (CC#17) and “Slider 6” to
Post IFX Pan (CC#08).
5. Rotate Sliders 5, 6 and the panning of the delay level
and the delay will change. You can sample the sound
while you modify it.
▼4–1: Menu Command
• 0: Panel–SW Solo Mode On ☞p.329
• 1: Exclusive Solo ☞p.329
• 2: Delete Sample ☞p.329
• 3: Copy Sample ☞p.330
• 4: Rename Sample ☞p.330
• 5: Move Sample ☞p.330
• 6:
Sample Mono To Stereo (Change Sample
Type)
☞p.331
• 7: Delete MS (Delete Multisample) ☞p.331
• 8: Copy MS (Copy Multisample) ☞p.332
• 9: Rename MS (Rename Multisample) ☞p.332
• 10: Move MS (Move Multisample) ☞p.332
• 11: Convert MS To Program (Convert Multisample To
Program) ☞p.333
• 12: MS Mono To Stereo ☞p.333
• 12: MS Stereo To Mono ☞p.333
• 13: Optimize RAM ☞p.334
• 14: Select Directory ☞p.334
• 15: Keyboard Display ☞p.334
• 16: Auto Sampling Setup ☞p.334
For more information, please see “Sampling: Menu
Command” on page 329.
4–1a
4–1b
4–1
Menu
To Next Page
Loading...
Need help?
General
