SEQ P7–4: KARMA 4 7–4–2: Dynamic MIDI
255
7–4–2: Dynamic MIDI
Dynamic MIDI is a function that lets you use this
instrument’s controllers and MIDI control messages to
control specific KARMA functions.
For more information, please see “7–2–3b: Dynamic MIDI”
on page 95 and page 174.
7–4–2a: Track Select, Tempo, RPPR
For more information, please see “2–1: Trim T01–08, 2–2:
Trim T09–16” on page 224.
7–4–2b: Dynamic MIDI
Select (Perf RTP Select) [1–2, 3–4, 5–6, 7–8]
Input (Dynamic MIDI Input Module) [A…D]
Source (Dynamic MIDI Source)
[Off, JS+Y (CC#01)…Velocity Outside Zone]
Bottom (Dynamic MIDI Range Bottom)
[000…127]
Top (Dynamic MIDI Range Top) [000…127]
Action (Dynamic MIDI Range Action)
[Momentary, Toggle, Continuous]
Destination (Dynamic MIDI Destination)
[Off, RT Params Control…Buffer Latch]
A/B/C/D [Off, On]
L (Last Triggered) [Off, On]
Polarity (Dynamic MIDI Polarity) [+, –, +/–, –/+]
For more information, please see “7–2–3b: Dynamic MIDI”
on page 95.
▼7–4–2: Menu Command
• 0: Memory Status ☞p.271
• 1: Panel–SW Solo Mode On ☞p.106
• 2: Exclusive Solo ☞p.107
• 3: Copy KARMA Module ☞p.114
• 4: Initialize KARMA Module ☞p.115
• 5: Copy Scene ☞p.115
• 6: Swap Scene ☞p.115
• 7: Capture Random Seed ☞p.116
• 8: FF/REW Speed ☞p.272
• 9: Set Location (Set Location for Locate Key) ☞p.272
• 10: Copy from Program ☞p.185
For more information, please see “Sequencer: Menu
Command” on page 271.
7–4–3: Names Master
Here you can select and edit the names of the master
KARMA Sliders and Switches.
7–4–3a: KARMA RTC Name
Select Real-Time Controls [Slider, Switch]
For more information, please see “Select Real-Time
Controls” on page 175.
7–4–3b: CAT., Names
Slider:
CAT. (Category)
Slider1…Slider8
[000 (no name)...571: Waveform Select [16]]
Switch1…8
[000 (no name)…571: Waveform Select [16]]
For more information, please see “CAT. (Category)” on
page 175.
▼7–4–3: Menu Command
• 0: Memory Status ☞p.271
• 1: Panel–SW Solo Mode On ☞p.106
• 2: Exclusive Solo ☞p.107
• 3: Copy KARMA Module ☞p.114
• 4: Initialize KARMA Module ☞p.115
• 5: Copy Scene ☞p.115
• 6: Swap Scene ☞p.115
• 7: Capture Random Seed ☞p.116
• 8: FF/REW Speed ☞p.272
• 9: Set Location (Set Location for Locate Key) ☞p.272
• 10: Copy from Program ☞p.185
For more information, please see “Sequencer: Menu
Command” on page 271.
7–4
–2b
7–4
–2a
7–4
–2
Menu
7–4
–3b
7–4
–3a
7–4
–3
Menu
To Next Page
Loading...
Need help?
General
