Program mode
114
Copy KARMA Module
Copy KARMA Module is available on all of the KARMA
pages, as well as the KARMA GE tab or KARMA RTC of the
Play page.
This command copies the settings of the KARMA Module
used by a specified program, combination, or song.
1. Select “Copy KARMA Module” to open the dialog box.
2. In From, select the copy source mode, bank, and
number.
You can use the front panel BANK SELECT I-A–U-G
switches to select the bank.
3. If you selected a combination or song as the copy-
source, select the module from which you want to copy.
4. As appropriate for the content that you want to copy,
turn “GE RTP Control & Scenes” On (checked).
For more information, please see “Settings copied by “Copy
KARMA Module”,” below.
5. If you want to copy performance realtime parameters,
Dynamic MIDI, and front panel settings, turn “Perf.
RTP & Panel Settings” On (checked).
For more information, please see “Settings copied by “Copy
KARMA Module”,” below.
6. If you want to copy the note and velocity settings of
pads 1–8, turn “Pads” On (checked).
7. To execute the Copy KARMA Module command, press
the OK button. To cancel, press the Cancel button.
Settings copied by “Copy KARMA Module”
When copying from a program
If GE RTP Control & Scenes and Perf. RTP & Panel
Settings are Off (unchecked), the following content is
copied.
• The GE selected by the copy-source KARMA module.
• Link to DT setting.
• Settings of the KARMA module parameters (7–1:
KARMA1– Trigger page, 7–1: KARMA1– Control page).
• 7–2: KARMA2– GE RTP page MIN, MAX, and VALUE
settings.
If you turn “GE RTP Control & Scenes” On (checked)
In addition to the content copied when GE RTP Control &
Scenes is Off (unchecked), the following content is copied.
• 7–2: KARMA2– GE RTP ASSIGN and POL. settings.
• The scene selected in the master buffer, the KARMA
Slider and KARMA Switch settings of each scene (0:
Play– KARMA RTC and 0: Play– Control Surface
“KARMA” settings).
• 7–2: KARMA2– Names controller name settings.
If you turn “Perf. RTP & Panel Setting” On (checked)
In addition to the content copied when “Perf. RTP & Panel
Settings” is Off (unchecked), the following content is copied.
• Tempo setting.
• Time Signature setting.
• KARMA ON/OFF switch setting.
• KARMA LATCH switch setting.
• 7–1: KARMA1– Drum Track Control page settings.
• 7–2: KARMA2– Perf RTP page settings.
• 7–2: KARMA2– Dynamic MIDI page settings.
When copying from a combination or song
If GE RTP Control & Scenes and Perf. RTP & Panel
Settings are Off (unchecked) when you copy from a
combination or song, the following content is copied.
• The GE selected for the copy-destination KARMA
module (including the GE realtime parameters).
• Link to DT setting of the copy-source KARMA module.
• KARMA module parameters (7–2: KARMA2– Trigger,
7–2: KARMA2– Control).
• 7–3: KARMA3– GE RTP MIN, MAX, and VALUE
settings.
If you turn “GE RTP Control & Scenes” On (checked)
In addition to the content copied when GE RTP Control &
Scenes is Off (unchecked), the following content is copied.
• 7–3: KARMA3– GE RTP ASSIGN and POL. settings.
• The KARMA slider and KARMA switch settings of each
scene in the copy-source buffer, and the currently
selected scene.
• 7–4: KARMA4– Names controller name settings.
• 7–4: KARMA4– Note Map settings.
If you turn “Perf. RTP & Panel Setting” On (checked)
In addition to the content copied when Perf. RTP & Panel
Settings is Off (unchecked), the following content is copied.
• Tempo setting.
• Time Signature setting.
• KARMA ON/OFF switch setting.
• KARMA LATCH switch setting.
• KARMA Module Control switch setting.
• 7–1: KARMA1– Scene Matrix “DT Run” page settings.
• 7–4: KARMA4– Perf RTP page settings.
• 7–4: KARMA4– Dynamic MIDI page settings.
The In (Input Channel) and Out (Output Channel)
(Combi/Seq 7–1–1c) settings of a combination or song
are not copied.
To Next Page
Loading...
Need help?
General
