Combination mode
170
7–2–5: Trigger A
Specifies the trigger conditions and latch on/off for the GE
that is selected for KARMA Module A.
7–2–5a: Module Parameter-Trigger
Control:
Quantize Trigger [Off, On]
Update On Release [Off, On]
For more information, please see “Control:” on page 84.
Delay:
Delay Start [Off, Fixed, 3 …4x1]
Delay Start Fixed [0000ms…5000ms]
For more information, please see “Delay:” on page 88.
Note (Trigger/Latch):
Note Trigger [Any, AKR, 1st, Dyn]
Note: With any of these settings, the trigger will be applied
by operations of the controller specified for Dynamic MIDI
(Prog 7–2–3), if Destination is set to Trigger Notes&Envs,
Trigger Note (see “Dynamic MIDI Sources & Destinations”
on page 601).
For more information, please see “Note Trigger” on page 88.
Note Latch [Off, On]
Note: In Combination mode, this can be turned on/off for
each KARMA Module. A KARMA Module for which this is
On (checked) will be in a Latch On condition when the
LATCH switch is on (LED lit).
For more information, please see “Note Latch” on page 88.
Envelope (Trigger/Latch):
Envelope1, Envelope2, Envelope3:
Envelope Trigger [Any, AKR, 1st, Dyn]
Envelope Latch [Off, Sus1, Rel1, Sus2, Rel2]
For more information, please see “Envelope (Trigger/
Latch):” on page 89.
Module Trigger:
Note and envelope triggering of a KARMA Module can be
controlled by the operation of another KARMA Module.
Trigger By Module [Off, A, B, C, D]
When the KARMA Module you specify here advances by
the length specified in GE Phrase Length, the KARMA
Module itself will be triggered automatically, starting the
phrase or pattern.
For example you could make settings so that harp glissando
phrases specified for each KARMA Module are triggered
consecutively. Alternatively, you could make settings so that
the four KARMA Modules are connected in series, and play
repeatedly.
GE Phrase Length [000…100%]
Specifies a percentage of a Module’s overall GE Phrase
Length after which triggering of this Module will occur.
When the KARMA Module chosen above advances by the
percentage of length specified here, this Module will be
automatically triggered.
This is valid except when Trigger By Module is Off.
Setting a Module to be triggered by a percentage of its
own phrase will have no additional effect.
Note: The actual overall GE Phrase Length is determined by
the number of Phase Pattern Steps, the Phase Length Mode,
and various other internal GE settings.
Cutoff Module A, B, C, D [Off, On]
When this Module’s effect is triggered, it can cutoff any
effects that are playing on the specified Modules.
This is mainly for use when you do not want effects from the
Modules overlapping each other, but want them to appear
continuous (i.e. 4 sax riffs, 4 different strumming effects,
etc.). For example, you could trigger different Modules in
separate areas of the keyboard, and only have one playing at
any particular time.
This can also be used to cycle back and forth between
Modules, with each Module shutting off the previous
Module when it is triggered in.
▼7–2–5: Menu Command
• 0: Write Combination ☞p.185
• 1: Panel–SW Solo Mode On ☞p.106
• 2: Exclusive Solo ☞p.107
• 3: Copy KARMA Module ☞p.114
• 4: Initialize KARMA Module ☞p.115
• 5: Copy Scene ☞p.115
• 6: Swap Scene ☞p.115
• 7: Capture Random Seed ☞p.116
• 8: Copy from Program ☞p.185
For more information, please see “Combination: Menu
Command” on page 185.
7–2–6: Trigger B,
7–2–7: Trigger C,
7–2–8: Trigger D
In these pages you can set the trigger parameters for
KARMA modules B, C, and D.
For more information, please see “7–2–5: Trigger A,” above.
7–2
–5a
7–2
–5
Menu
To Next Page
Loading...
Need help?
General
