Double Size
521
166: St/Cross Long Delay
(Stereo/Cross Long Delay)
This is a stereo delay, and can by used as a cross-feedback
delay effect in which the delay sounds cross over between
left and right by changing the feedback routing. You can set
a maximum of 2,730msec for the delay time.
167: Hold Delay
This effect records the input signal and plays it back
repeatedly. You can control the start of recording and reset
via a modulation source. Easy to use for real-time
performances.
a: Loop Time [msec]
With Auto, the loop time is automatically set. Otherwise,
you can specify the loop time.
When Auto is selected, the Loop Time is automatically set to
the time it takes for a performance recorded while the
Modulation Source or Manual REC Control is on. However,
if the time length exceeds 10,800msec, the loop time will be
automatically set to 10,800msec.
c: Time Over?
You can set the delay time up to 10,800msec. If the delay
time exceeds this limit, the error message “OVER!” appears
in the display. Set the delay time parameters so that this
message will not appear. Time Over? is only a display
parameter.
aStereo/Cross Stereo, Cross
Switches between stereo delay
and cross-feedback delay
b
L Delay Time
[msec]
0.0...2730.0
Sets the delay time for the left
channel
c
R Delay Time
[msec]
0.0...2730.0
Sets the delay time for the right
channel
d
L Feedback –100...+100
Sets the feedback amount for
the left channel
Src Off...Tempo
Selects the modulation source
of feedback amount
Amt –100...+100
Sets the modulation amount of
the left channel feedback
e
R Feedback –100...+100
Sets the feedback amount for
the right channel
Amt –100...+100
Sets the modulation amount of
the right channel feedback
f
High Damp
[%]
0...100
Sets the damping amount in
the high range p.476
g
Low Damp
[%]
0...100
Sets the damping amount in
the low range p.476
h
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of
the input level p.472
Src Off...Tempo
Selects the modulation source
for the input level p.472
iSpread –50...+50
Sets the width of the stereo
image of the effect sound
p.476
j
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount
for Wet/Dry
Delay
Delay
Stereo/Cross
Left
Right
Feedback
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Input Level D-mod
Input Level D-mod
High Damp Low Damp
High Damp
Low Damp
Spread
Stereo/Cross
a
Loop Time
[msec]
Auto,
1...10800
Sets Automatic loop time setup
mode or specifies loop time
p.521
b
Loop BPM
Sync
Off, On
Specifies whether delay time is
set in milliseconds, or as a note
value relative to tempo p.522
c
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system
tempo; 40–300 sets the tempo
manually for this individual
effect p.522
Time Over? ---, OVER!
An error indication that appears
if delay time exceeds the upper
limit when MIDI/Tempo
Sync=On
d
Loop Base
Note
...
Selects the type of notes to
specify the delay time p.522
Times x1...x32
Sets the number of notes to
specify the delay time p.522
e
REC Control
Src
Off...Tempo
Selects control source for
recording p.522
f
RST Control
Src
Off...Tempo
Selects control source for reset
p.522
g
Manual REC
Control
REC Off,
REC On
Sets the recording switch
p.522
h
Manual RST
Control
Off, RESET Sets the reset switch p.522
i
Pan
L100...L1, C,
R1...R100
Sets the stereo image of the
effect
Src Off...Tempo
Selects the modulation source
of stereo image of the effect
Amt –100...+100
Sets the modulation amount of
stereo image of the effect
j
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount
for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Pan
Delay
D
-mod
D
-mod
Loop Time: Auto/ ...5400ms
+
Tempo
BPM
BPM
Base Note x Times
REC Control
RST Control
To Next Page
Loading...
Need help?
General
