Chorus, Flanger, and Phaser (Cho/Fln Phaser)
459
g: High/Low Split Point
This parameter sets the frequency that splits the high and
low range. Only the high range will be sent to the chorus
block.
h: Feedback
Sets the feedback amount of the chorus block. Increasing the
feedback will allow you to use the effect as a flanger.
028: St. Biphase Mod.
(Stereo Biphase Modulation)
This stereo chorus effect adds two different LFOs together.
You can set the Frequency and Depth parameters for each
LFO individually. Depending on the setting of these LFOs,
very complex waveforms will create an analog-type,
unstable modulated sound.
j
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount
for Wet/Dry
a
LFO1
Waveform
Triangle,
Sine
Selects LFO1 waveform
LFO2
Triangle,
Sine
Selects LFO2 waveform
Phase Sw
0 deg,
180 deg
Switches the LFO phase
difference between left and
right
b
LFO1
Frequency
[Hz]
0.02...30.00 Sets the LFO1 speed
Src Off...Tempo
Selects the modulation source
of LFO1&2 speed
LFO1 Amt
–30.00...
+30.00
Sets the modulation amount of
LFO1 speed
c
LFO2
Frequency
[Hz]
0.02...30.00 Sets the LFO2 speed
Amt
–30.00...
+30.00
Sets the modulation amount of
LFO2 speed
d
LFO1 Type
Individual,
Common1,
Common2
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.448
CmnLFO
Offset [deg]
–180...+180
Sets the phase offset when
LFO1 Type = Common 1 or
Common 2 p.448
e
LFO2 Type
Individual,
Common1,
Common2
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.448
CmnLFO
Offset [deg]
–180...+180
Sets the phase offset when
LFO2 Type = Common 1 or
Common 2 p.448
f
Depth1 0...100
Sets the depth of LFO1
modulation
Src Off...Tempo
Selects the modulation source
of LFO1&2 modulation depth
Amt –100...+100
Sets the modulation amount of
LFO1 modulation depth
g
Depth2 0...100
Sets the depth of LFO2
modulation
Amt –100...+100
Sets the modulation amount of
LFO2 modulation depth
Chorus/Flanger
Left
Right
Feedback
180 [degree]
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
LFO1: Tri / Sine
LFO2: Tri / Sine
Chorus/Flanger
High Damp
h
L Pre Delay
[msec]
0.0...50.0
Sets the delay time for the left
channel p.458
R Pre Delay
[msec]
0.0...50.0
Sets the delay time for the right
channel p.458
i
Feedback –100...+100
Sets the feedback amount
p.459
High Damp
[%]
0...100
Sets the damping amount in
the high range
j
Wet/Dry
–Wet...
–1 : 99, Dry,
1 : 99...Wet
Sets the balance between the
effect and the dry input
p.450
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount
for Wet/Dry
LFO1
LFO2
Bi-Phase Modulation LFO
Depth1
Depth2
+
To Next Page
Loading...
Need help?
General
