Korg M3 - 3-2: Preference

Sampling mode
318
If you have not yet executed Cut or Copy, such as
immediately after power-on, the new index will be
created according to the Create Zone Preference
settings (0–3a, 3–2a) Position, Zone Range, and
Original Key Position.
Cut
This deletes the selected index. At the same time, the
contents of the deleted index are copied to the Insert buffer.
Copy
This copies the content of the selected index to the Insert
buffer.
Create
This creates an index. When you press the Create button, a
new index will be created according to the settings of
Position, Zone Range, and Original Key Position (3–2c, 0–
3a) (0–1a).
▼3–1: Menu Command
• 0: Panel–SW Solo Mode On ☞p.329
• 1: Exclusive Solo ☞p.329
• 2: Delete Sample ☞p.329
• 3: Copy Sample ☞p.330
• 4: Rename Sample ☞p.330
• 5: Move Sample ☞p.330
• 6:
Sample Mono To Stereo (Change Sample
Type)
☞p.331
• 7: Delete MS (Delete Multisample) ☞p.331
• 8: Copy MS (Copy Multisample) ☞p.332
• 9: Rename MS (Rename Multisample) ☞p.332
• 10: Move MS (Move Multisample) ☞p.332
• 11: Convert MS To Program (Convert Multisample To
Program) ☞p.333
• 12: MS Mono To Stereo ☞p.333
• 12: MS Stereo To Mono ☞p.333
• 13: Optimize RAM ☞p.334
• 14: Pitch BPM Adjust ☞p.351
• 15: Select Directory ☞p.334
• 16: Keyboard Display ☞p.334
For more information, please see “Sampling: Menu
Command” on page 329.
3–2: Preference
3–2a: Create Zone Preference
Position [Right (to Selected Index),
Left (to Selected Index)]
Zone Range [1 Key...127 Keys]
Original Key Position [Bottom, Center, Top]
Here you can specify the default settings for indices that are
created by executing Create (3–1b, 0–1b). New indexes will
be created according the settings you specify here. You are
free to modify the settings of an index later. Also, when you
execute Insert (3–1b), the Position setting specified here will
be used. For more information, please see “0–3a: Create
Zone Preference” on page 307.
▼3–2: Menu Command
• 0: Panel–SW Solo Mode On ☞p.329
• 1: Exclusive Solo ☞p.329
• 2: Delete Sample ☞p.329
• 3: Copy Sample ☞p.330
• 4: Rename Sample ☞p.330
• 5: Move Sample ☞p.330
• 6:
Sample Mono To Stereo (Change Sample
Type) ☞p.331
• 7: Delete MS (Delete Multisample) ☞p.331
• 8: Copy MS (Copy Multisample) ☞p.332
• 9: Rename MS (Rename Multisample) ☞p.332
• 10: Move MS (Move Multisample) ☞p.332
• 11: Convert MS To Program (Convert Multisample To
Program) ☞p.333
• 12: MS Mono To Stereo ☞p.333
• 12: MS Stereo To Mono ☞p.333
• 13: Optimize RAM ☞p.334
• 14: Pitch BPM Adjust ☞p.351
• 15: Select Directory ☞p.334
• 16: Keyboard Display ☞p.334
For more information, please see “Sampling: Menu
Command” on page 329.
3–2a
3–2
Menu