Lenze i950

Address Designaon Default seng Data type Factor A M
0x2022:035 Device commands: Restart Device O / ready [0] U8 X
0x2022:036 Device commands: Export Logbook O / ready [0] U8 X
0x2022:037 Device commands: Delete Logles O / ready [0] U8 X
0x2022:038 Device commands:
Acvate loaded applicaon O / ready [0] U8 X
0x2022:039 Device commands: Load TA default sengs O / ready [0] U8 X
0x2022:040 Device commands: Parameter-Backup O / ready [0] U8 CX
0x2022:041 Device commands: Restart extended safety O / ready [0] U8 X
0x2022:042 Device commands: Upload applicaon O / ready [0] U8 X
0x2022:043 Device commands: Restore O / ready [0] U8 CX
0x2030 CRC parameter set - (Read only) U32 1 X
0x2100:001 Brand protecon: PIN set 0 I32 1 X
0x2100:002 Brand protecon: PIN input 0 I32 1 X
0x2100:003 Brand protecon: Encrypon 0 U8 1 X
0x2110:014 SHOM: Delete home posion O / ready [0] U8 X
0x2114:001 Parameter set Idencaon: Parameter set version - (Read only) U16 -
0x2114:002 Parameter set Idencaon: Parameter set CRC 0 U32 1 -
0x2115:001 Parameter set informaon: Parameter set status - (Read only) U8 X
0x2115:002 Parameter set informaon: Safety module CRC - (Read only) U32 1 X
0x2115:003 Parameter set informaon: Last valid CRC - (Read only) U32 1 X
0x2115:004 Parameter set informaon: Parameter seng me
stamp
x s (Read only) U32 1 X
0x2115:005 Parameter set informaon: Parameter set error
informaon 1
- (Read only) U32 1 X
0x2115:006 Parameter set informaon: Parameter set error
informaon 2
- (Read only) U32 1 X
0x2115:007 Parameter set informaon: Parameter set error
informaon 3
- (Read only) U32 1 X
0x2118:001 SD-In: Sensor type: SD-In1: Sensor type - (Read only) U8 -
0x2118:002 SD-In: Sensor type: SD-In2: Sensor type - (Read only) U8 -
0x2118:003 SD-In: Sensor type: SD-In3: Sensor type - (Read only) U8 -
0x2118:004 SD-In: Sensor type: SD-In4: Sensor type - (Read only) U8 -
0x2119:001 SD-In: Discrepancy me: SD-In1: Discrepancy me x ms (Read only) U16 1 -
0x2119:002 SD-In: Discrepancy me: SD-In2: Discrepancy me x ms (Read only) U16 1 -
0x2119:003 SD-In: Discrepancy me: SD-In3: Discrepancy me x ms (Read only) U16 1 -
0x2119:004 SD-In: Discrepancy me: SD-In4: Discrepancy me x ms (Read only) U16 1 -
0x211A:001 SD-In: Input delay: SD-In1: Input delay x ms (Read only) U16 1 -
0x211A:002 SD-In: Input delay: SD-In2: Input delay x ms (Read only) U16 1 -
0x211A:003 SD-In: Input delay: SD-In3: Input delay x ms (Read only) U16 1 -
0x211A:004 SD-In: Input delay: SD-In4: Input delay x ms (Read only) U16 1 -
0x211B Input image - (Read only) U32 HX
0x211C:001 Status bits of inputs: SD-In1 - (Read only) BOOLEAN 1 X ●
0x211C:002 Status bits of inputs: SD-In2 - (Read only) BOOLEAN 1 X ●
0x211C:003 Status bits of inputs: SD-In3 - (Read only) BOOLEAN 1 X ●
0x211C:004 Status bits of inputs: SD-In4 - (Read only) BOOLEAN 1 X ●
0x211C:005 Status bits of inputs: AIS Dig-In - (Read only) BOOLEAN 1 X
0x211C:006 Status bits of inputs: AIE Dig-In - (Read only) BOOLEAN 1 X
0x211C:007 Status bits of inputs: IRS Dig-In - (Read only) BOOLEAN 1 X
0x211C:008 Status bits of inputs: IRL Dig-In - (Read only) BOOLEAN 1 X
0x2120:001 SD-Out: Source S-Bus: SD-Out1: Source S-Bus - (Read only) U8 -
0x2121:001 SD-Out logic funcon: SD-Out1 logic funcon - (Read only) U8 -
0x2122 Output image - (Read only) U16 HX
0x2123:001 Status bits of outputs: SD-Out1 - (Read only) BOOLEAN 1 X ●
0x2124 CAS: Quelle SD-In - (Read only) U8 -
0x2125:001 CAS: Cascading: CAS: Stop delay x ms (Read only) U16 1 X
* Default seng depending on the size.
Appendix
P
arameter aribute list
464