Mitsubishi GOT2000 Series - Page 14

A - 12
8.4.12 When connecting multiple GOTs ........................................................................................ 8 - 40
8.4.13 When using a PLC CPU in the direct mode........................................................................ 8 - 40
8.4.14 When connecting to a Q4ARCPU redundant system ......................................................... 8 - 41
8.4.15 When monitoring the Q170MCPU, Q170MSCPU(-S1) ...................................................... 8 - 41
8.4.16 Troubleshooting .................................................................................................................. 8 - 41
9. MELSECNET/H CONNECTION (PLC TO PLC NETWORK),
MELSECNET/10 CONNECTION (PLC TO PLC NETWORK)
9.1 Connectable Model List ................................................................................................................... 9 - 2
9.1.1 PLC/Motion controller CPU................................................................................................... 9 - 3
9.1.2 MELSECNET/H network module.......................................................................................... 9 - 8
9.1.3 MELSECNET/H (NET/10 mode), MELSECNET/10 network module ................................... 9 - 8
9.2 System Configuration ...................................................................................................................... 9 - 9
9.2.1 Connecting to optical loop system ........................................................................................ 9 - 9
9.2.2 Connecting to the coaxial bus system ................................................................................ 9 - 11
9.3 GOT Side Settings ......................................................................................................................... 9 - 13
9.3.1 Setting communication interface (Communication settings)............................................... 9 - 13
9.3.2 Communication detail settings............................................................................................ 9 - 13
9.3.3 Routing parameter setting ..................................................................................................9 - 14
9.4 PLC side setting when connecting to MELSECNET/H .................................................................. 9 - 16
9.4.1 System configuration .......................................................................................................... 9 - 16
9.4.2 Switch setting of MELSECNET/H network module............................................................. 9 - 16
9.4.3 Parameter setting ............................................................................................................... 9 - 17
9.4.4 [Controller Setting] of GT Designer3................................................................................... 9 - 20
9.5 PLC side setting when connecting to MELSEC/10 ........................................................................ 9 - 21
9.5.1 Connecting to MELSECNET/H network module................................................................. 9 - 21
9.5.2 Connecting to MELSECNET/10 network module (QnA Series) ......................................... 9 - 26
9.5.3 Connecting to MELSECNET/10 network module (A Series) .............................................. 9 - 30
9.6 Precautions.................................................................................................................................... 9 - 34
10. CC-Link IE CONTROLLER NETWORK CONNECTION
10.1 Connectable Model List ................................................................................................................. 10 - 2
10.1.1 PLC/Motion controller CPU.................................................................................................10 - 2
10.1.2 CC-Link IE Controller Network communication unit............................................................ 10 - 7
10.2 System Configuration .................................................................................................................... 10 - 8
10.2.1 Connecting to optical loop system ...................................................................................... 10 - 8
10.3 GOT side settings .......................................................................................................................... 10 - 9
10.3.1 Setting communication interface (Communication settings)............................................... 10 - 9
10.3.2 Communication detail settings............................................................................................ 10 - 9
10.3.3 Routing parameter setting ................................................................................................ 10 - 10
10.4 PLC Side Setting ......................................................................................................................... 10 - 12
10.5 Precautions.................................................................................................................................. 10 - 18
11. CC-Link IE FIELD NETWORK CONNECTION
11.1 Connectable Model List ................................................................................................................. 11 - 2
11.1.1 PLC/Motion controller CPU.................................................................................................11 - 2
11.1.2 CC-Link IE Field Network communication unit ................................................................... 11 - 7
11.2 System Configuration .................................................................................................................... 11 - 8