SeaDoo GTI - User Manual

Questions and Answers

S
Sandra WardSep 14, 2025
Why SeaDoo Boat has unusual engine noise and/or vibration (4-TEC series)?
- J
  Jeremy HesterSep 14, 2025
  If your 4-TEC series SeaDoo Boat experiences unusual engine noise and/or vibration, it could be caused by a worn chain tensioner or guide, a stretched chain and/or worn out sprockets, loose sprocket screws, a worn out hydraulic element inside rocker arm(s) or damaged lifter, rocker arm screws not tightened, heavy wear on crankshaft and/or balancer shaft bearings, crankshaft and balancer shaft not aligned, heavy wear on thrust washers, a defective supercharger, or a missing/defective air intake hose. Replace the chain tensioner or guide, chain and sprockets. Retorque sprocket screws. Replace faulty rocker arm(s) and/or lifters. Retorque rocker arm screws. Check and replace the thrust washers. Check and replace the air intake hose or clamps.
M
Matthew HuffmanAug 27, 2025
Why does SeaDoo Boat engine turn slowly?
- M
  Marco KramerAug 28, 2025
  If your SeaDoo Boat engine turns slowly, it could be due to loose battery cable connections, a discharged or weak battery, a restriction in the jet pump, a partial seizure in the jet pump, partial engine hydro-lock, partial engine seizure, a worn starter, the timing chain not guided by the chain guide, or the outside temperature being too low. Check, clean, and tighten the battery cable connections. Check, charge, or replace the battery. Check and clean the jet pump.
J
johnathan00Aug 29, 2025
What causes SeaDoo GTI engine to continually backfire?
- T
  Todd GuzmanAug 29, 2025
  If your SeaDoo Boat engine continually backfires, it could be caused by a weak spark, issues with the spark plugs, incorrect ignition timing, a defective encoder wheel/CPS, problems with the rotary valve, carburetor issues, or intake or exhaust valve leaks. Clean or replace the spark plugs. Check and reset the ignition timing. Check and reset the rotary valve. Check the carburetor. Pressure check the engine for intake or exhaust valve leaks.
P
pkerrAug 31, 2025
What to do if SeaDoo GTI engine stops when running?
- C
  Christine ParrishAug 31, 2025
  If your SeaDoo Boat engine stops while running, consider these potential causes: the spark plug heat range being too high, improper ignition timing, a compression ratio that is too high, poor injection oil quality, electrical noise, low air pressure, engine stalling at idle, air in the fuel rail, or the engine starting but stopping after approximately 2 seconds. Check and change the spark plug to the correct range. Check and reset the ignition timing. Install genuine parts if the compression ratio is too high. Use proper BOMBARDIER injection oil. Check the air delivery circuit for leaks. Syphon the reservoir and refill with fresh fuel. Check the fuel delivery system for proper fuel pressure and delivery.
E
everettbrianSep 1, 2025
Why SeaDoo GTI Boat engine detonation or pinging?
- R
  Rachel SimmonsSep 1, 2025
  If your SeaDoo Boat engine experiences detonation or pinging, possible causes include: issues with the ignition, a spark plug heat range that is too high, high engine/exhaust temperature, fuel octane too low or poor fuel quality, a disconnected or faulty knock sensor, a bad knock sensor connection, or a bad ECM connection. Check and reset the ignition. Check and change the spark plug to the correct range. Use good quality fuel.
A
Amber BrownSep 3, 2025
Why SeaDoo Boat engine cannot reach maximum RPM?
- B
  Bethany DelacruzSep 3, 2025
  If your SeaDoo Boat engine cannot reach maximum RPM, the following reasons might be the cause: the RAVE valve not opening, a faulty water regulator valve, low fuel pressure, a jet pump related problem, limp home mode being activated, exhaust system blockage or muffler damage, exhaust gases in the bilge due to a leak, a defective supercharger, or battery voltage being too low. Check the fuel pump pressure output. Check and repair any exhaust system blockage or muffler damage. Check the exhaust system for leaks.
S
Steven HensonNov 23, 2025
Why SeaDoo GTI engine misfires, runs irregularly?
- C
  Christopher MooreNov 24, 2025
  If your SeaDoo Boat engine misfires or runs irregularly, several factors could be responsible: a weak spark, a faulty ECM or MPEM, a defective encoder wheel/CPS, too much oil supplied to the engine, bad ignition coil wiring or connector, poor engine ground, a lean fuel mixture, a dirty carburetor, low fuel pressure, leaking crankshaft seals or intake manifold, a restricted fuel valve, a loose carburetor, stale or water-fouled fuel, a dirty or restricted fuel filter, or clogged fuel or direct injectors. It may also be due to a defective sensor or ECM/MPEM. Check the spark, verify the heat range and gap, and replace if necessary. Adjust the oil injection pump. Check the wiring condition and grounding of the ignition coil. Check, clean, and repair the engine ground. Check and refill the fuel....
R
Randy MartinSep 15, 2025
What causes low or no engine oil pressure (4-TEC series) in SeaDoo GTI Boat?
- R
  Robert FosterSep 16, 2025
  If your 4-TEC series SeaDoo Boat has low or no engine oil pressure, it could be due to a low oil level, a leaking gasket, oil leaking out of the weep hole, a defective oil pressure sensor, a malfunctioning oil pump, an oil regulator valve sticking open, or heavy wear on plain bearings. Refill the oil to the correct level. Replace any leaking gaskets. Replace the oil seal on the pump shaft if oil is leaking out of the weep hole. Check and replace the oil pressure sensor. Clean the rotor and check wear limits if the oil pump is malfunctioning. Clean or replace the oil regulator valve.
J
Joseph LeonSep 12, 2025
What to do if SeaDoo Boat engine starts but runs only at idle speed?
- S
  Shelly WallSep 12, 2025
  If your SeaDoo Boat engine starts but only runs at idle speed, it could be due to the system being in limp home mode or a broken or loose throttle cable. Change or readjust the throttle cable.
J
John LangSep 9, 2025
Why SeaDoo GTI Boat engine oil contamination (milky) (4-TEC series)?
- A
  Austin BrooksSep 9, 2025
  If you notice milky engine oil in your 4-TEC series SeaDoo Boat, it may be caused by a water and oil mixture leaking out of the weep hole, a leaking cylinder head gasket, loose screws on the cylinder head, PTO housing, or oil separator, oil contamination due to metal or plastic particles, or water ingestion. Replace both seals if there is a water and oil mixture leaking out of the weep hole and change the oil. Replace the gasket if the cylinder head gasket is leaking and change the oil. Retorque loose screws and change the oil. Replace possibly damaged parts and change the oil.