Index
S7-1200 Programmable controller
System Manual, V4.2, 09/2016, A5E02486680-AK
1595
Label (jump label), 302
LED (read LED status), 450
LEFT (read the left characters of a character
string), 364
legacy TCON, TDISCON, TSEND, and TRCV
instructions, 868
legacy TRCV_C (receive data via Ethernet
(TCP)), 849
legacy TSEND_C (send data via Ethernet
(TCP)), 849
legacy USS status codes, 1246
LEN (determine the length of a character
string), 362
LIMIT (set limit value), 262
LN (form natural logarithm), 263
LOG2GEO (Determine the slot from the hardware
identifier), 546
LOWER_BOUND (read out ARRAY low limit), 277
MAX (get maximum), 261
MAX_LEN (maximum length of a character
string), 361
MB_CLIENT, 1171
MC_ChangeDynamic (change dynamic settings for
the axis), 754
MC_CommandTable, 751
MC_Halt (pause axis), 740
MC_Home (home axis), 737
MC_MoveAbsolute (position axis absolutely), 742
MC_MoveJog (move axis in jog mode), 749
MC_MoveRelative (position axis relatively), 745
MC_MoveVelocity (move axis at predefined
velocity), 747
MC_Power (release/block axis), 733
MC_ReadParam (read parameters of a technology
object), 758
MC_Reset (confirm error), 736
MC_WriteParam (write to parameters of a
technology object), 756
MID (read the middle characters of a character
string), 364
MIN (get minimum), 261
MOD (return remainder of division), 258
Modbus_Comm_Load (Configure SIPLUS I/O or
port on the PtP module for Modbus RTU), 1194
Modbus_Master (Communicate using SIPLUS I/O
or the PtP port as Modbus RTU master), 1198
Modbus_Slave (Communicate using SIPLUS I/O or
the PtP port as Modbus RTU slave), 1206
ModuleStates (read module status information of a
module), 474
monitor, 1327
monitoring status or value, 1326
motion control, 731
MOVE (move value), 265
MOVE_BLK (move block), 265
MUL (multiply), 257
MUX (multiplex), 329
N (scan operand for negative signal edge), 233
N_TRIG (scan RLO for negative signal edge), 234
N= box and N coil (set operand on negative signal
edge), 233
NE_ElemType (Compare data type for UNEQUAL
with the data type of a tag), 253
NE_Type (Compare data type for UNEQUAL with
the data type of a tag), 253
NEG (create twos complement), 259
NORM_X (normalize), 296
NOT (invert RLO), 229
NOT_NULL (Query for UNEQUALS zero
pointer), 254
NOT_OK (check invalidity), 252
OK (check validity), 252
OR (logic operation), 326
OUT_Range (value outside range), 251
P (scan operand for positive signal edge), 233
P_TRIG (scan RLO for positive signal edge), 234
P= box and P coil (set operand on positive signal
edge), 233
P3964_Config (Configuring the 3964(R)
protocol), 1120
PEEK and POKE variations, 206, 281
PID_Compact (universal PID controller with
integrated tuning), 592
PID_Temp (universal PID controller that allows
handling of temperature control), 610
Port_Config (port configuration), 1110
PROFIBUS distributed I/O, 384
PROFINET distributed I/O, 384
program control (SCL), 316
PRVREC (make data record available), 413
PUT (write data to a remote CPU), 986
QRY_CINT (query cyclic interrupt parameters), 426
QRY_DINT (query time-delay interrupt status), 432
QRY_TINT (query status of time of day
interrupt), 431
R (reset output), 230
R_TRIG (set tag on positive signal edge), 234
RALRM (receive interupt), 394
RCVREC (receive data record), 411
RD_ADDR (determine the IO addresses from the
hardware identifier), 550
RD_LOC_T (read local time), 339
RD_SYS_T (read time-of-day), 339
RDREC (read data record), 385
To Next Page
Loading...
