Siemens SIMATIC S7-1200 - Page 1596

Index
S7-1200 Programmable controller
1596 System Manual, V4.2, 09/2016, A5E02486680-AK
RE_TRIGR, 109
RE_TRIGR (restart cycle monitoring time), 309
READ_BIG (Read data in big little endian
format), 283
READ_DBL (read from data block in load
memory), 538
READ_LITTLE (Read data in little endian
format), 283
Receive_Config (receive configuration), 1115
Receive_P2P (receive Point-to-Point), 1126
Receive_Reset (receiver reset), 1128
RecipeExport (recipe export), 502
RecipeImport (recipe import), 504
REPEAT (SCL), 322
REPLACE (replace characters in a character
string), 367
reset output, 230
RESET_BF (reset bit field), 231
RET (return), 306
RETURN (SCL), 325
RIGHT (read the right characters of a character
string), 364
ROL (rotate left) and ROR (rotate right), 333
ROUND (round numerical value), 294
RS (reset/set flip-flop), 231
RT (reset timer), 236
RTM (runtime meters), 344
RUNTIME (Measure program runtime), 314
S (set output), 230
S_CONV (convert character string), 347
S_MOV (move chracter string), 346
SCALE_X (scale), 296
scaling analog values, 43
SCL conversion instructions, 291
SEL (select), 329
Send_Config (send configuration), 1112
Send_P2P (send Point-to-Point data), 1122
Serialize, 272
set output, 230
SET_BF (set bit field), 231
SET_CINT (set cyclic interrupt parameters), 424
Set_Features (set advanced features), 1132
SET_TIMEZONE (set time zone), 343
SET_TINTL (set date and time of day interrupt), 428
SGN_GET (get RS232 signals), 1129
SHL (shift left) and SHR (shift right), 332
Signal_Set (set RS232 signals), 1130
SIN (form sine value), 263
SQR (form square), 263
SQRT (form square root), 263
SR (set/reset flip-flop), 231
SRT_DINT (start time-delay interrupt), 432
status, 1327
STP (exit program), 310
Strg_TO_Chars (convert character string to array of
CHAR), 357
STRG_VAL (convert character string to numerical
value), 347
SUB (subtract), 257
SWAP (swap bytes), 276
SWITCH (jump distributor), 304
T_ADD (add times), 336
T_COMBINE (combine times), 337
T_CONFIG (configure interface), 901
T_CONV (convert times and extract), 335
T_DIAG, 880
T_DIFF (time difference), 337
T_RESET, 878
T_SUB (subtract times), 336
TAN (form tangent value), 263
TCON, 857
TDISCON, 857
time, 335
timer, 236
TM_MAIL (send email), 1301
TOF (off-delay timer), 236
TON (on-delay timer), 236
TONR (on-delay retentive timer), 236
TP (pulse timer), 236
TRCV, 857
TRCV_C, 837, 921
TRUNC (truncate numerical value), 294
TSEND, 857
TSEND_C, 837, 920
TURCV (receive data via Ethernet (UDP)), 895
TUSEND (send data via Ethernet (UDP)), 895
UFILL_BLK (fill block uninterruptible), 275
UMOVE_BLK (move block uninterruptible), 265
UPPER_BOUND (read out ARRAY high limit), 279
USS status codes, 1160
USS_Drive_Control (Swap data with drive), 1154
USS_Port_Scan (Edit communication via USS
network), 1153
USS_Read_Param (readout parameters from the
drive), 1157
USS_Write_Param (change parameters in the
drive), 1158
VAL_STRG (convert numerical value to character
string), 347
VARIANT_TO_DB_ANY (Convert VARIANT to
DB_ANY), 299
VariantGet (Read VARIANT tag value), 285
VariantPut (Write VARIANT tag value), 286