Siemens SIMATIC S7-1200 System Manual

Index
S7-1200 Programmable controller
System Manual, V4.2, 09/2016, A5E02486680-AK
1597
versions of
instructions, 45, 836, 848, 856, 867, 1149, 1170, 11
93, 1235, 1249, 1269
WHILE (SCL), 321
WR_LOC_T (set local time), 339
WR_SYS_T (set time-of-day), 339
WRIT_DBL (write to data block in load
memory), 538
WRITE_BIG (Write data in big endian format), 283
WRITE_LITTLE (Write data in little endian
format), 283
WRREC (write data record), 385
WWW (synchronizing user-defined Web
pages), 1059
x box (FBD XOR logic operation), 228
XOR (logic operation), 326
Instructions, legacy
MB_CLIENT (communicate via PROFINET as
Modbus TCP client), 1250
MB_COMM_LOAD (configure port on the PtP
module for Modbus RTU), 1270
MB_MASTER (communicate via the PtP port as
Modbus master), 1272
MB_SERVER (communicate via PROFINET as
Modbus TCP server), 1257
MB_SLAVE (communicate via the PtP port as
Modbus slave), 1278
PORT_CFG (configure communication parameters
dynamically), 1218
RCV_CFG (configure serial receive parameters
dynamically), 1221
RCV_PTP (enable receive messages), 1229
RCV_RST (delete receive buffer), 1231
SEND_CFG (configure serial transmission
parameters dynamically), 1220
SEND_PTP (transmit send buffer data), 1226
SGN_GET (Query RS232 signals), 1232
SGN_SET (set RS-232 signals), 1233
USS_DRV (Swap data with drive), 1240
USS_PORT (Edit communication via USS
network), 1239
USS_RPM (readout parameters from the
drive), 1243
USS_WPM (change parameters in the drive), 1244
Inter-character gap, 1102
Interrupts
ATTACH (attach an OB to an interrupt event), 420
CAN_DINT (cancel time-delay interrupt), 432
DETACH (detach an OB from an interrupt
event, 420
interrupt latency, 105
overview, 92
QRY_DINT (query time-delay interrupt status), 432
SRT_DINT (start time-delay interrupt), 432
Intro standard Web page, 1017
INV (create ones complement), 327
IO system, data exchange, 931
IO2MOD (Determine the hardware identifier from an
I/O address, 548
IO-Link
address space, 1493
changing parameters in runtime, 1494
configuring, 1493
data record, 1495
device profile, 1488
device storage, 1490
diagnostics, 1498
diagram, 1492
error messages, 1494, 1496, 1498
functions, 1489
LED display, 1496
parameters, 1493
pin assignment, 1491
replacing, 1489
reset to factory settings, 1490
IO-Link Master signal module, 1485
IP address, 815, 815
assigning, 810, 819
assigning online, 813
configuring, 814
configuring the online CPU, 1316
device configuration, 170
MAC address, 814
IP router, 814
IS_ARRAY (Check for ARRAY), 254
IS_NULL (Query for EQUALS ZERO pointer), 254
ISO on TCP
ad hoc mode, 828
ISO on TCP protocol, 825
Isolation guidelines, 77
ISO-on-TCP
connection configuration, 807
connection IDs, 828
parameters,
832
J
JavaScript, standard Web pages, 1083
Jerk limit, 730
JMP (jump if RLO = 1), 302
JMP_LIST (define jump list), 303
JMPN (jump if RLO = 0), 302

Siemens SIMATIC S7-1200 Specifications

General

CPU Type	CPU 1211C, CPU 1212C, CPU 1214C, CPU 1215C, CPU 1217C
Communication	PROFINET
Analog Inputs	2
Analog Outputs	2
Power Supply	24V DC
Expansion Modules	Signal Modules (SM), Communication Modules (CM)
Programming Languages	LAD, FBD, SCL
Dimensions	90 mm x 100 mm x 75 mm
Program Memory	50 KB to 150 KB (depending on model)