YASKAWA V1000 Technical Manual

PGo .......................................................... 250, 251, 263, 272
PG Open-Circuit Detection Time (for Simple PG V/f Control)....... 347
Phase Order Selection....................................................... 333
PID Accel/Decel Time ...................................................... 335
PID Control Selection Error................................................ 251
PID Control Selection Fault ................................................ 276
PID Disable................................................................... 351
PID Feedback .......................................................... 355, 376
PID Feedback High Detection Level...................................... 335
PID Feedback High Level Detection Time............................... 335
PID Feedback Loss .................................. 250, 251, 257, 269, 354
PID Feedback Loss Detection Level ...................................... 335
PID Feedback Loss Detection Time....................................... 335
PID Feedback Reference Missing Detection Selection................. 335
PID Function Setting ........................................................ 334
PID Input (feedback) ........................................................ 376
PID Input Limit .............................................................. 335
PID Input Switch............................................................. 351
PID Integral Hold............................................................ 351
PID Integral Reset ........................................................... 351
PID Offset Adjustment...................................................... 334
PID Output.................................................................... 376
PID output fault .............................................................. 286
PID Output Gain Setting.................................................... 335
PID Output Level Selection ................................................ 335
PID Output Limit ............................................................ 334
PID Output Lower Limit.................................................... 335
PID Output Reverse Selection ............................................. 335
PID Primary Delay Time Constant........................................ 334
PID Setpoint .................................................................. 376
PID Set Point ................................................................. 355
PID Setpoint / User Display................................................ 335
PID Setpoint and Display Digits........................................... 335
PID Setpoint Scaling ........................................................ 335
PID Setpoint Selection ...................................................... 335
PID Setpoint Value .......................................................... 335
PID Sleep Delay Time ...................................................... 335
PID Sleep Function Start Level............................................ 335
PID Soft Starter .............................................................. 351
PM Speed Feedback Detection Suppression Gain ...................... 263
Poor Speed Control Accuracy.............................................. 284
Poor Speed Control Accuracy Above Base Speed in Open-loop Vector
Motor Control Method ...................................................... 288
Power Detection Filter Time ............................................... 336
Power Specifications 200 V Class Models ......................... 319, 320
Power Specifications 400 V Class Models ......................... 321, 322
Previous Fault ................................................................ 373
Program Lockout ............................................................ 351
Programming Mode ..................................................82, 83, 84
Proportional Gain Setting (P) .............................................. 334
Protective Covers, Reattaching ..............................................54
Protective Covers, Removing ........................................... 53, 54
Pull-In Current ............................................................... 366
Pull-In Current Compensation Time Constant............... 263, 287, 366
Pull-In Current during Accel/Decel for PM.............................. 264
Pull Out Detection ........................................................... 264
Pull-Out Detection........................................................... 250
Pulse Train Input Bias....................................................... 357
Pulse Train Input Filter Time .............................................. 357
Pulse Train Input Gain ...................................................... 357
Pulse Train Input Scaling ............................................. 262, 356
Pulse Train Monitor Scaling ............................................... 357
PWM Data Error............................................................. 254
PWM Feedback Data Fault................................................. 250
PWM Feedback Fault ....................................................... 255
Q
q1-01 to q6-07................................................................ 369
q-axis ACR Output .......................................................... 377
R
RAM Fault.............................................................. 250, 255
Rated Current Setting Alarm ......................................... 252, 277
Rated Frequency ........................................... 319, 320, 321, 322
Rated Output Capacity (kVA) ....................................... 319, 320
Rated Slip Error........................................................ 252, 278
Rated Voltage .............................................. 319, 320, 321, 322
Reference Sample Hold..................................................... 351
Regenerative Torque Limit................................................. 355
REMOTE .......................................................................86
Replacement Parts .................................................294, 327, 29
Reset Command Active..................................................... 353
Restart Enabled .............................................................. 353
Reverse Direction............................................................ 353
Reverse Jog ................................................................... 351
Reverse Operation Selection ............................................... 332
Reverse Operation Selection 2 by PID Output........................... 336
Reverse Regenerative Torque Limit ...................................... 362
Reverse Run Command (2-Wire sequence) .............................. 351
Reverse Torque Limit ....................................................... 362
REV Torque Limit........................................................... 355
rH ........................................................................ 250, 263
Rotational Auto-Tuning............................................... 100, 281
rr.......................................................................... 250, 263
RTS Control Selection ...................................................... 356
rUn....................................................................... 251, 272
Run Command (2-Wire sequence 2) ...................................... 351
Run Command at Power Up................................................ 333
Run Command Input Error ................................................. 251
Run Command Selection ............................................. 280, 332
Run Command Selection 2 ................................................. 333
Run Command Selection during Program................................ 333
Run Command Selection Error ............................................ 251
Run Command Selection Results.......................................... 376
S
Safe Disable Input .............................................................63
Safe Disable Signal Input................................................... 269
Safety Hazard Definitions ....................................................13
Safety Information.............................................................13
SC........................................................................ 250, 264
S-Curve Characteristic at Accel End ...................................... 337
S-Curve Characteristic at Accel Start ..................................... 337
S-Curve Characteristic at Decel End ...................................... 337
S-Curve Characteristic at Decel Start ..................................... 337
S-Curve Characteristics ..................................................... 248
SE ........................................................................ 251, 272
Search Operation Voltage Limit ........................................... 336
SEr ....................................................................... 250, 264
Serial Communication Terminals............................................64
Serial Communication Transmission Error ........................ 250, 266
Setup Mode ................................................................ 83, 87
Shielded Twisted-Pair Cables................................................66
Short-Circuit Brake.......................................................... 354
Short-Circuit Brake (N.C.) ................................................. 352
Short-Circuit Brake (N.O.) ................................................. 352
Short Circuit Brake Time at Start.......................................... 333
Side-by-Side Setup ............................................................39
Simple V/f with PG.......................................................... 276
Index
YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual
473

YASKAWA V1000 Specifications

General

Input Voltage	3-Phase 200-240VAC, 3-Phase 380-480VAC
Output Voltage	3-Phase 200-240VAC, 3-Phase 380-480VAC
Output Frequency	0-400 Hz
Control Method	V/f control
Overload Capacity	150% for 60 seconds
Protection Functions	Overcurrent, Overvoltage, Undervoltage, Overheating, Short Circuit, Ground Fault
Communication Options	Modbus RTU
Ambient Temperature	-10 to +50°C (14 to 122°F)
Storage Temperature	-20°C to +65°C (-4°F to 149°F)
Humidity	95% (non-condensing)
Cooling Method	Forced Air Cooling
Enclosure	IP20