xx
4-7 Default DHCP Server Parameters.................................................................................................... 4-20
4-8 Configuring Pool Parameters ........................................................................................................... 4-23
5-1 User Account and Password Parameter Defaults by Security Mode ................................................. 5-7
6-1 File Management Commands ............................................................................................................ 6-8
7-1 PoE Powered Device Classes............................................................................................................ 7-2
7-2 PoE Settings Supported on Enterasys Devices ................................................................................. 7-4
7-3 PoE Show Commands ..................................................................................................................... 7-10
8-1 Displaying Port Status ....................................................................................................................... 8-7
8-2 Linkflap Default Parameters ............................................................................................................... 8-9
8-3 Link Flap Detection Show Commands ............................................................................................. 8-11
8-4 Transmit Queue Monitoring Tasks ................................................................................................... 8-11
9-1 Default VLAN Parameters .................................................................................................................. 9-9
9-2 Displaying VLAN Information............................................................................................................ 9-14
9-3 VLAN Terms and Definitions ............................................................................................................ 9-14
10-1 Default Authentication Parameters................................................................................................. 10-12
10-2 PWA Guest Networking Privileges Configuration........................................................................... 10-17
10-3 Displaying MultiAuth Authentication Configuration......................................................................... 10-20
10-4 Authentication Configuration Terms and Definitions ...................................................................... 10-28
11-1 LAG2 Port Priority Assignments....................................................................................................... 11-5
11-2 LAG Port Parameters ....................................................................................................................... 11-7
11-3 Default Link Aggregation Parameters............................................................................................... 11-9
11-4 Managing Link Aggregation............................................................................................................ 11-10
11-5 Displaying Link Aggregation Information and Statistics.................................................................. 11-11
11-6 LAG and Physical Port Admin Key Assignments ........................................................................... 11-13
11-7 Link Aggregation Configuration Terms and Definitions ..................................................................11-15
12-1 SNMP Message Functions............................................................................................................... 12-2
12-2 SNMP Terms and Definitions ........................................................................................................... 12-5
12-3 SNMP Security Models and Levels .................................................................................................. 12-6
12-4 Default Enterasys SNMP Configuration ........................................................................................... 12-8
12-5 Commands to Review SNMP Settings...........................................................................................12-18
13-1 LLDP Configuration Commands....................................................................................................... 13-7
13-2 LLDP Show Commands ................................................................................................................. 13-10
13-3 Enterasys Discovery Protocol Configuration Commands............................................................... 13-10
13-4 Enterasys Discovery Protocol Show Commands ........................................................................... 13-11
13-5 Cisco Discovery Protocol Configuration Commands...................................................................... 13-12
13-6 Cisco Discovery Protocol Show Commands .................................................................................. 13-12
14-1 Syslog Terms and Definitions........................................................................................................... 14-3
14-2 Syslog Message Components.......................................................................................................... 14-6
14-3 Syslog Command Precedence......................................................................................................... 14-8
14-4 Syslog Server Default Settings.............................................................................................
.......... 14-10
15-1 Maximum SID Capacities Per Platform ............................................................................................ 15-6
15-2 Spanning Tree Port Roles .............................................................................................................. 15-13
15-3 Spanning Tree Port States ............................................................................................................. 15-13
15-4 Multiple Spanning Tree Instance Support ......................................................................................15-16
15-5 MSTI Characteristics for Figure 15-10............................................................................................ 15-19
15-6 Spanning Tree Port Default Settings.............................................................................................. 15-21
15-7 BPDU Interval Defaults................................................................................................................... 15-22
15-8 Commands for Monitoring MSTP ................................................................................................... 15-29
15-9 Commands for Monitoring SpanGuard...........................................................................................15-31
15-10 Commands for Monitoring Loop Protect.........................................................................................15-35
15-11 Spanning Tree Terms and Definitions ............................................................................................ 15-36
16-1 Admin Rule Parameters ................................................................................................................... 16-5
16-2 Policy Rule Traffic Descriptions/Classifications................................................................................ 16-6
16-3 Valid Data Values for Traffic Classification Rules ............................................................................ 16-6
16-4 Non-Edge Protocols ......................................................................................................................... 16-8
16-5 Displaying Policy Configuration and Statistics................................................................................ 16-11
To Next Page
Loading...
Need help?
General