Alternate Modulation Sources (AMS) Alternate Modulation settings
593
increasing velocity, the EG levels will change more
greatly. At the maximum velocity, the Start Level will
stay at +00, but the Attack Level will change to +99 and
the Break Level will change to –99.
EG Time —
Pitch EG (Prog 2–8c)
Filter EG (Prog 3–1–5c)
Amp EG (Prog 4–3d)
EG times can be controlled by the Common LFO, keyboard
tracking, controllers, or tempo etc.
You can specify an “Intensity” value for each EG segment
(“Attack,” “Decay,” “Slope,” “Release”). EG times are
determined by the Alternate Modulation value when the
preceding point is reached. For example, the Alternate
Modulation value at the moment the envelope reaches the
attack level will determine the decay time.
If “Intensity” is set to a value of 8, 17, 25, 33, 41, or 49, the
corresponding time can be multiplied by a maximum of 2, 4,
8, 16, 32, or 64 times (or divided by 1/2, 1/4, 1/8, 1/16, 1/
32, 1/64).
• Select JS +Y:CC#01 for “AMS,” and set “AMS Intensity”
to +8, “At” to +, “Dc” to –, and “Sl” and “Rl” to 0. When
you move the joystick in the +Y direction, the Attack
Time will be lengthened by a maximum of 2 times. The
Decay Time will be shortened by a maximum of 1/2.
The Slope and Release times will not change.
LFO Frequency (Prog 5–1a)
The frequency of LFO 1, 2 or Common LFO can be
controlled by the EG, keyboard tracking, controllers, or
tempo etc.
You can also use the LFO2 frequency to modulate LFO1, or
use the Common LFO frequency to modulate LFO 1/2.
If Intensity is set to a value of 16, 33, 49, 66, 82, or 99, the
corresponding frequency can be multiplied by a maximum
of 2, 4, 8, 16, 32, or 64 times (or divided by 1/2, 1/4, 1/8, 1/
16, 1/32, 1/64).
• Select JS +Y:CC#01 for AMS, and set Intensity to +16.
When you move the joystick in the +Y direction, the LFO
frequency will be increased by a maximum of 2 times. If
you set Intensity to –16 and move the joystick in the +Y
direction, the LFO frequency will be decreased by up to
1/2.
LFO Frequency AMS Intensity (Prog 5–1b)
You can use the EG, keyboard tracking, controllers, or tempo
etc. to control the intensity of the AMS that controls the
frequency of the LFO 1, 2, or Common LFO.
For example if you’re using the pitch EG to modulate the
LFO frequency, you could use a separate AMS to control the
depth of this effect.
• Set AMS to a controller such as SW 1 or 2, so that the
pitch EG will lightly control the LFO frequency when the
switch is off, and more deeply when the switch is on.
LFO Shape (Prog 5–1a)
You can use a EG, keyboard tracking, controllers, or tempo
etc. to control the shape of the LFO 1, 2, or Common LFO
waveform. You can also use the LFO2 frequency to
modulate LFO1, or use the Common LFO frequency to
modulate LFO 1/2.
• You can control the LFO waveform by setting AMS to a
controller such as JS+Y, and operating the controller
when desired.
Common LFO Reset (Prog 5–8a)
You can use a controller or tempo etc. to reset the Common
LFO.
• By setting AMS to Gate 1, you can make the Common
LFO reset when a note is played from a state in which all
notes are off. For example, this will ensure that a filter
sweep always starts from the same place.
• You can set AMS to a controller such as JS+Y: CC#01,
and operate the controller when you want to reset the
LFO.
To Next Page
Loading...
Need help?
General
