YASKAWA GA700 - Page 1049

YASKAWA ELECTRIC SIEP C710617 05F YASKAWA AC Drive GA700 Technical Manual 1049
Protective function .............................................. 981
Software version
Display procedure ............................................... 188
Speed Agreement
Parameter ......................................................... 965
Speed Detection
Parameter ......................................................... 965
Speed Estimation Speed Search .................................... 714
Speed limit
Parameter ......................................................... 791
Speed search function
Operation during momentary power loss..................... 951
Speed Search function
Parameter ......................................................... 713
Stall Prevention function
Parameter ......................................................... 955
Stationary Auto-Tuning
Induction motor .................................................. 192
PM motor ......................................................... 193
Precautions ....................................................... 200
Stationary Auto-Tuning for Line-to-Line Resistance............ 192
Precautions ....................................................... 201
Stator resistance Auto-Tuning ...................................... 193
Precautions ....................................................... 201
STo ..................................................................... 372
SToF.................................................................... 372
Stop command
LOCAL/REMOTE Run Selection............................. 699
STOP key.............................................................. 141
STOP Key Function Selection.................................... 1018
Stop Position Gain ................................................... 790
Stopping Method Selection ......................................... 699
STPo ................................................................... 358
Surge protective device
Connection........................................................ 126
SvE ..................................................................... 358
T
Temperature
Environment....................................................... 35
Terminal block ........................................................ 108
Configuration of main circuit terminal block ................. 76
Control circuit terminal block functions...................... 105
I/O terminals function selection switches .................... 112
Terminal function selection ......................................... 114
Terminal A1 ................................................ 112, 114
Terminal A2 ................................................ 112, 114
Terminal A3 ................................................ 112, 115
Terminal AM ............................................... 112, 115
Terminal FM................................................ 112, 115
Termination resistor
Setting switch .................................................... 116
Test run
Checklist .......................................................... 215
Fine tuning........................................................ 204
Procedure ......................................................... 149
Procedure for no-load test run ................................. 202
Procedure for test run with actual load ....................... 202
Thermal overload relay
Connection........................................................ 123
Tightening torque
Control circuit terminals ........................................ 109
Main circuit terminals............................................ 82
TiM
Fault ............................................................... 359
Minor Fault ....................................................... 372
Timer function
Parameter ......................................................... 721
Torque compensation
Parameter ......................................................... 791
Torque Compensation
Parameter ......................................................... 759
Torque Control
Parameter ......................................................... 790
Switching to/from Speed Control ............................. 793
Torque limit function
Parameter ......................................................... 974
Torque reference
Parameter ......................................................... 791
Trend Plot
Monitors .......................................................... 162
Troubleshooting
Code Displayed .................................................. 331
No Code Displayed.............................................. 389
Troubleshooting without Fault Display ........................... 389
TrPC.................................................................... 372
Tuning.................................................................. 749
U
U2, U3 Initialization ............................................... 1024
UL Type 1
Attach protective cover .......................................... 55
UL3
Fault ............................................................... 359
Minor Fault ....................................................... 372
UL4
Fault ............................................................... 359
Minor Fault ....................................................... 372
UL5
Fault ............................................................... 359
Minor Fault ....................................................... 373
Undertorque detection
Parameter ......................................................... 969
Unit of measurement setting
Acceleration and deceleration times .......................... 752
Up 2 command
Parameter ................................................... 784, 788
Up command
Parameter ................................................... 784, 788
Up Command ................................................... 870, 872
USB port............................................................... 141
Connecting a PC ................................................. 117
User Monitor Select afterPowerUp ...............................1011
User Parameter Default Value .................................... 1018
User-Set Display Units Max Value .............................. 1013
User-SetDisplayUnits Dec Display .............................. 1013
Uv ...................................................................... 373
Speed Search Selection at Start................................ 720
Uv1 ..................................................................... 359
Detection level settings ......................................... 952
Uv2 ..................................................................... 360
Uv3 ..................................................................... 360
V
vAEr.................................................................... 387
V/f Pattern............................................................. 798
Second Motor .................................................... 809
V/f Pattern Display Unit........................................... 1012
Verify
Parameters (keypad and drive)................................. 171
vFyE.................................................................... 387
Vibration-resistant..................................................... 35
W
Wire gauge
Control circuit terminals ........................................ 109
Wire gauges