191
M4.3-1055-059
04 Rev. 10/09
ELECTRICAL
ACCESS 123...System
F13.2 menu will not appear if F13.1 is set to disable.
F13.2 Flow = ____; Press the right arrow and use the
up and down arrows to select 3.8 through 30.3 lpm (1
through 8 gpm). Press enter/ return to return to F13.1.
Press the left arrow to accept input and return to F13.
Press the down arrow to continue.
F14 Accessory 3 = ____; Sets the volume of hydraulic
oil flow supplied to the third accessory.
If F13 is set to disable, F1 will not appear.
Press the right arrow to enter the following submenus
(F14.1 and F14.2).
The second and third accessory must be high flow.
F14.1 Mode = ____; Since the second function must
be high flow, these choices are enable or disable.
Press the right arrow and use the up and down arrows
to enable or disable this feature. Press enter/return to
accept input and return to F14.1. Press down arrow to
continue.
F14.2 menu will not appear if F14.1 is set to disable.
F14.2 Flow = ____; Press the right arrow and use the
up and down arrows to select 3.8 through 30.3 lpm (1
through 8 gpm). Press enter/return to accept input and
return to F14.2. Press the left arrow to return to F14.
Press the down arrow to continue.
F15 Productivity = ____; When enabled, this feature
permits increased travel speeds when the load is less
than 455 kg (1000 lb). For this feature to function, the
truck must be equipped with a load sensor.
Press the right arrow and use the up and down arrows
to enable or disable this feature. Press enter/return to
accept input and return to F15. Press the down arrow
to continue.
F17 Raise Cutout = ___; In this feature, truck must be
equipped with mast limit switches. If this feature is en-
abled and the truck is equipped with mast limit
switches, raise will cutout at the predetermined height
of a mast limit switch.
Press the right arrow and use the up and down arrows
to enable or disable this feature. Press enter/return to
accept input and return to F17. Press the down arrow
to continue.
F20 Pressure Regulator = ___; This feature must be
enabled on trucks including an accessory with a pres-
sure regulator (like a carton clamp), so the proportional
accessory relief valve (PVAR) can be calibrated. Press
the right arrow and use the up and down arrows to en-
able or disable feature. Press enter/return to accept in-
put and return to F20.
Trucks equipped with the electronic pressure regulator
option have a proportional accessory relief valve
(PVAR) included in the hydraulic manifold instead of an
accessory relief valve RVA. PRVA allows multiple relief
settings for attachments.
Press the down arrow to continue.
F22 Message Mode = ___; This feature changes infor-
mation displayed during operation. Different messages
may be displayed in the Level 1 Message Mode, which
allows you to select the message(s) that will be dis-
played while in Level 1 Message Mode.
Select from: Bdi (battery percent of charge), Hours
(hour meter reading), Odometer (total distance truck
has traveled in miles), Trip (total distance truck has
traveled since last reset), Timer (stopwatch) or All (al-
lows operator to determine message using display but-
tons).
Press the right arrow and use the up and down arrows
to select a message. After selecting message, press
enter/return to accept input and return to F22. Press
the down arrow to continue.
F24 Battery Retainer = ___; If battery retainers are not
in place on trucks equipped with optional battery re-
straint switches and this feature is enabled, then travel
and hydraulic functions will not be permitted.
Press the right arrow and use the up and down arrows
to enable or disable this feature. Press enter/return to
accept input and return to F24. Press the down arrow
to continue.
F25 Hour Meter = ___; Changes the hour meter that
will be displayed during operation. H1 records the pres-
ence pedal switch ON time. H2 also records the pres-
ence pedal switch ON time plus the timeout period that
the truck is left unattended before the display shuts
down.
Press the right arrow and then use the up and down
arrows to change between H1 and H2. Press the enter/
return button to accept input and return to F25.
Crown 2007 PF15628-59 Rev. 10/09
To Next Page
Loading...