ELECTRICAL
ACCESS 123...System
196
M4.3-1055-064
04 Rev. 10/09
P14.4 Plug = ___; Allows adjustment of the plugging
effort above free lift in relation to the travel handle po-
sition. The longest plugging distance will occur with the
handle near the neutral position and a setting of 1. The
shortest plugging distance is achieved when the han-
dle is fully applied in one direction or the other, with a
setting of 9. Factory setting is 5. Press the right arrow
and use the up/down arrows to select desired setting.
Press the enter/return button to accept input. The
menu will return to P14.4. Press the down arrow button
to continue.
P14.5 Brake = ___; Adjusts the motor braking effort
above free lift. Press the right arrow and use the up/
down arrows to select desired setting. The range is 1
for the least motor braking effort to 9 for the maximum
motor braking effort, in relationship to the brake pedal
position. Factory setting is 5. Press the enter/return
button to accept input. The menu will return to P14.5.
Press the down arrow to continue.
P99 Load factory defaults - Loads factory settings for
all Performance menu levels. Press the right arrow to
select this feature. Use up/down arrows to select
"Sure? Y" to accept factory settings. Press the enter/
return button to accept. Display returns to P99, press
the left arrow to exit to main menu. This procedure can
be done at any time while in the performance menu.
Utilities
The Utilities menu allows you to view module and soft-
ware part numbers and activate the tow mode. Part
numbers are available in service Level 2 and Level 3.
Tow mode is only available in Level 3.
Power up the truck. Navigate to the Service Menu and
enter Level 3. Scroll to Utilities and press the right ar-
row.
U1 Part Numbers; For access to module and software
part numbers, press the right arrow. Use the up and
down arrows to scroll through the submenus.
The software part number includes two dash numbers.
The last dash number denotes the software version.
For example, if ACCESS 1 software part number is
122729-001-02, the part number ends with a dash 02
indicating the software version is 2.
U1.1 ACCESS 1; Press the right arrow to view
ACCESS 1 part number. Press the down arrow to view
software part number. Press the left arrow to return to
U1.1 then press the down arrow to continue.
U1.2 ACCESS 2; Press the right arrow to view
ACCESS 2 part number. Press the down arrow to view
software part number. Press the left arrow to return to
U1.2 then press the down arrow to continue.
U1.3 ACCESS 3; Press the right arrow to view
ACCESS 3 part number. Press the down arrow to view
software part number. Press the left arrow to return to
U1.3 then press the down arrow to continue.
U1.4 ACCESS 7; Press the right arrow to view
ACCESS 7 part number. Press the down arrow to view
software part number. Press the left arrow to return to
U1.4 then press the left arrow again to return to U1 Part
Numbers. Press the down arrow to continue.
U2 Tow Mode; (Level 3 Only) this menu allows activa-
tion of tow mode. With tow mode active, the parking
brakes will release. Before making tow mode active, be
sure to read and follow the procedures in the "Control
of Hazardous Energy" section in this service manual.
For tow mode to be active, the floor pedals must be
depressed.
1. To activate tow mode, press the right arrow.
2. The following message will be displayed.
Tow Mode = Off
3. Press the right arrow and use the up/down arrow to
change OFF to ON.
4. Press enter to activate tow mode.
5. To de-activate Tow Mode, turn the key switch OFF
then ON.
Crown 2007 PF15628-64 Rev. 10/09
To Next Page
Loading...