193
M4.3-1055-061
04 Rev. 10/09
ELECTRICAL
ACCESS 123...System
E1 Chron History - Press the right arrow to view a
chronological listing of the last 16 events beginning
with the most recent event logged. Use the up and
down arrows to scroll through the events. Use the right
arrow for more information about each event.
E1.1 Last; Press the right arrow to view the event code
"Code = ___". Press the down arrow to view the hour
meter reading "Hour = ___ Hr" when the event was
logged. Press the down arrow again to view the battery
state of charge, "SOC = ___ %" when the event was
logged. Press the left arrow to return to E1.1 then press
the down arrow to continue.
E1.2 Last -1 through E1.16 Last -15; The remaining
event codes follow the same pattern as E1.1. Follow
the instructions given in E1.1 to view the event code,
the hour meter reading and the state of battery charge
when the event occurred. Press the left arrow to return
to E1. Press the down to continue.
E2 Accum History; Press the right arrow to view the
number of times a specific event has occurred. Use the
up and down arrows to scroll through the events. Press
the left arrow to return to E2. Press the down to con-
tinue.
E3 Clear History; Clear History permits two ways of
clearing event codes; Clear Chronological and Clear
All. Press the right arrow.
E3.1 Clear Chronological; This menu permits clear-
ing Chronological History (E1) which still allows access
to Accumulated History (E2) of events. Press the right
arrow to clear chronological event code log history.
Use the up and down arrows to select "Sure? Y" and
press enter to clear. Menu will return to E3.1 Clear
Chronological. Press the down arrow to continue.
E3.2 Clear All; This menu permits clearing both Chro-
nological (E1) and Accumulated (E2) History. Press
the right arrow to clear all stored event history. Use the
up and down arrows to select "Sure? Y" and press en-
ter to clear. Menu will return to E3.2 Clear All. Press the
left arrow twice to return to Events.
Performance
P1, P2, and P3 are the three performance levels that
may be selected when in level 1 as long as F10 User
Performance is enabled. If User Performance is dis-
abled, the operator will then be locked in at the P1 set-
tings. The other option is enabling the F11 User Codes
option which allows any one of the three performance
levels to be assigned to the 25 different user codes.
Any setting under the three performance levels can be
higher, lower or the same as the setting under any
other performance.
If changes have been made in the sub menus, pressing
the left arrow at the first level menu will prompt "Save?
N" in the settings. Use the up and down arrows to se-
lect "Save? Y" then press enter/return to save settings.
Within the P1, P2 and P3 menus you can adjust the
following parameters.
P1.1 Forward = ___ mph; Maximum forward (forks
first) traction speed. Press the right arrow and use up/
down arrows to select desired speed. Range is from
1.0 to 7.2 mph. Factory setting is 7.2 for P1; 6.2 for P2
and 6.0 for P3. Press the enter/return to accept input.
The menu will return to P1.1. Press the down arrow to
continue.
P1.2 Rev = ___ mph; Maximum reverse (power unit
first) traction speed. Press the right arrow and use the
up/down arrows to select desired speed. Range is 1.0
to 7.2 mph for standard trucks, and 1.0 to 7.8 mph for
trucks equipped with the productivity package. Factory
setting is 7.8 for P1; 7.2 for P2 and 6.0 for P3. Press the
enter/return button to accept input. The menu will re-
turn to P1.2. Press the down arrow to continue.
P1.3 Accel = ___; Acceleration rate (time for truck to
go from stop to top speed). Press the right arrow and
use the up/down arrows to select desired acceleration
rate. Range is 1 for the longest acceleration time to 9
for the shortest acceleration time. Factory setting is 7
for P1; 6 for P2 and 5 for P3. Press the enter/return
button to accept input. The menu will return to P1.3.
Press the down arrow to continue.
P1.4 Tilt = ___; Allows overall tilt speed adjustment.
Press the right arrow and use the up/down arrows to
select desired speed. Range is 1 (slowest) to 9 (fast-
est). Factory setting is 9 for P1, P2 and P3. Press the
enter/return button to accept input. The menu will re-
turn to P1.4. Press the down arrow to continue.
Depending on the trucks configuration the following ac-
cessory speed settings may or may not be shown. Ref-
erence F12, F13 and F14 in the Features menu.
P1.5 Accessory 1 = ___; Allows accessory 1 overall
speed adjustment. Press the right arrow and use the
up/down arrows to select desired speed. Range is 1
(slowest) to 9 (fastest). Factory setting is 9 for P1; 7 for
P2 and 5 for P3. Press the enter/return button to accept
input. The menu will return to P1.5. Press the down ar-
row to continue.
Crown 2007 PF15628-61 Rev. 10/09
To Next Page
Loading...